Jump to content
RemedySpot.com

Re: RADAR HELP!

Rate this topic


Recommended Posts

Guest guest
Posted

Brand: TES Model No.: TES92

I believe for HF

Measures: 50Mhz-3.5Ghz in a variety of units:mV/m , V/m , μA/m , mA/m , μW/m²

, mW/m² , μW/cm².

I have had trouble with it ever since I bought it. I don't understand it. In

these measurements, what are the " safety levels " ?

Kris

________________________________

From: charles <charles@...>

Sent: Thu, April 22, 2010 11:33:30 AM

Subject: Re: Re: RADAR HELP!

What kind of electrosmog meter ?

Brand?

Type?

LF or HF ?

Greetings,

Claessens

member Verband Baubiologie

www.milieuziektes.nl

www.milieuziektes.be

www.hetbitje.nl

checked by Norton

Re: Re: RADAR HELP!

>

> Radar and it's frequencies.

> I do not have a meter that will measure this for me. I have an

> electrosmog meter. Never does it read while they are flying. Does that

> mean the radar is too high for it to read? I have never understood that

> meter and have had trouble with it since I bought it last year. :(

>

>

------------------------------------

Guest guest
Posted

Well, in the last couple of days, we built a " cage " around our couch. We made

the frame out of PVC pipe 1/2 " . Took Reynolds Heavy Duty Aluminum foil and

placed it under the couch on the floor, folding over twice and taping each seam

with aluminum tape. We did this on the top, sides and ends. My Hubby had to of

course help me in and close the one open end with me lying on the couch inside.

I had my oxygen tubing so I was able to have enough air from the tank on the

outside of the cage. Grounded it to a stake outside.

IT WORKED!!!! We had three jets fly overhead several swoops and Very very VERY

close. Made the house shake a little. (Maybe they didn't like the cage!) I

didn't tremor nor did I get the jabbing chest pains! :)

I was jittering inside some but did NOT tremor!

It was tough to make b/c the foil easily has little pin holes poked through all

over. I crawled inside and saw them all. :( So then I took some lighter duty

foil and doubled up on the sides, top and one end. Hard to do the end I have to

crawl through, but at least that took care of most of the pin holes.

I had such a bad reaction to the Denny Foil we used last year that I was very

skeptical that this would work. God answered our prayers. It did.

SO, then for the trailer, we have to put in a vapor barrier yet anyway, so we

should probably go ahead and use a product like the reflectix before the wall

board? We're going to change our flooring and go with that aluminum tread solid

stuff.

What do you think?

Do you want to see pics? i can easily attach them.

Kris

________________________________

From: Bill Bruno <wbruno@...>

Sent: Thu, April 22, 2010 1:53:51 PM

Subject: Re: Re: RADAR HELP!

Silver and copper are the best. But aluminum is best per $. But if it is

77GHz you need a really fine weave. 200 per inch might not be necessary,

but the wavelength is about (1/77) feet which is like 1/6 of an inch. You

definitely need to have spacing more dense that 12 per inch, and several

times that is better. So really nothing below 40 per inch.

Try to have overlap all around the windows... if it leaks in it will bounce

around. You will get reduction... whether it will be enough I can't

predict.

On Thu, Apr 22, 2010 at 10:18 AM, K <kfarming@...> wrote:

>

>

> Sorry I didn't respond til now. Wasn't able to get to my emails yesterday.

> wouldn't let me in for some reason. ;( Jets have been flying late

> afternoon and at night everyday this week so I have been really suffering

> lately.

>

> SIlver Lame Fabric:

> one site said is was made of Polyester. Amazon's site showed it was made

> out of 49% Nylon, 51% Metallic Yarn and quite a bit more expensive. What

> materials should I look for in this fabric? Is metallic yarn a metal yarn?

> Also, can you explain my fogged brain a little more how this will give me

> more protection?

>

> Military jets:

> They are supposed to be getting new jets with digital equipment on them.

> Again, will I be exposed to higher levels?

>

> Water jugs.

> I can try that. See if it works.

>

> Radar and it's frequencies.

> I do not have a meter that will measure this for me. I have an electrosmog

> meter. Never does it read while they are flying. Does that mean the radar is

> too high for it to read? I have never understood that meter and have had

> trouble with it since I bought it last year. :(

>

> ________________________________

> From: snoshoe_2 <snoshoe_2@... <snoshoe_2%40>>

> <%40>

> Sent: Wed, April 21, 2010 2:39:18 AM

> Subject: Re: RADAR HELP!

>

>

> I just thought of something else...

>

> But first maybe you can try something we talked on here a few years back to

> help - the silver lame fabric from Walmart or fabric stores, a few yards of

> that to add a couple more layers of protection. You can use it as a blanket

> in the cage, and it reflects your body's own fir, which is nice too, unless

> it's really hot out.

> Someone here tested it for it's impedence ability and found it does has

> some.

>

> Now by other thought, :( . It may be that being military jets, they have

> started using the x-ray imaging in some of their onboard tech. like some

> satellites do. The only answer I can to that is can you say " lead paint " . If

> you're sensitive to xrays, it has a burning sensation, similar to too much

> sun exposure, but you may feel it deeper.

>

> Something to try for heart, if you can hold a jug of water in front of your

> heart, it seems to help absorb some of problem and reduce the pain, don't

> know about that frequency, but I've tried it a couple times in town now,

> when my heart was being bothered. If I have a cup of coffee in my hand say,

> I'll hold it in front of my heart till it passes and it seems to reduce the

> effect. If it's coming from your back, well maybe make a wall lined with

> plastic water bottles in your room?

> ~ Snoshoe

>

>

> >

> > Ok, So I am getting more and more sensitive to the military RADAR as well

> as obtaining new symptoms even from commercial jets. this stabbing pain into

> my chest and out through my mid back. The Heavy duty faraday canopy is not

> shielding me good enough anymore.

> >

> > What do I do?

> > Kris

> >

> >

> >

> >

> >

> >

Guest guest
Posted

You should use the unit μW/m².

If yoy do have a damaged immune system, you may become electrosensitive

between 200 and 2.000 μW/m².

When you have become electrosensitive, it is possible that you may have

reactions at less than 1 μW/m².

Normally, aircraft radar lies over you max of 3.5 GHz, so you cannot measure

them.

Greetings,

Claessens

member Verband Baubiologie

www.milieuziektes.nl

www.milieuziektes.be

www.hetbitje.nl

checked by Norton

Re: Re: RADAR HELP!

>

> Radar and it's frequencies.

> I do not have a meter that will measure this for me. I have an

> electrosmog meter. Never does it read while they are flying. Does that

> mean the radar is too high for it to read? I have never understood that

> meter and have had trouble with it since I bought it last year. :(

>

>

------------------------------------

Guest guest
Posted

Brand: TES Model No.: TES92

I believe for HF

Measures: 50Mhz-3.5Ghz in a variety of units:mV/m , V/m , μA/m , mA/m ,

μW/m² , mW/m² , μW/cm².

I have had trouble with it ever since I bought it. I don't understand it. In

these measurements, what are the " safety levels " ?

Kris

Hello Kris,

What kind of trouble have you had? We might be able to assist you.

We recommend using the mV/m units. It is the unit the meter is actually

measuring (electric field). The other units are calculated (by the meter)

from the mV/m. Also, it is a nice sensitive unit.

the formula for converting is this:

mW/cm2 = (V/m)2 / 3770

[the 2's are exponents]

Emil

________________________________

From: charles <charles@...>

Sent: Thu, April 22, 2010 11:33:30 AM

Subject: Re: Re: RADAR HELP!

What kind of electrosmog meter ?

Brand?

Type?

LF or HF ?

Greetings,

Claessens

member Verband Baubiologie

www.milieuziektes.nl

www.milieuziektes.be

www.hetbitje.nl

checked by Norton

Re: Re: RADAR HELP!

>

> Radar and it's frequencies.

> I do not have a meter that will measure this for me. I have an

> electrosmog meter. Never does it read while they are flying. Does that

> mean the radar is too high for it to read? I have never understood that

> meter and have had trouble with it since I bought it last year. :(

>

>

------------------------------------

Guest guest
Posted

I have that same meter. I like how simple it is and fairly rugged.

But it has some silly features. Hard to see why anyone would want the units

in A/m. I use mV/m, but if you're not used to those it would make sense to

just use mW/m^2 because it's a more standard unit.

At low frequencies your hand will affect the reading.

When cold the unit reads far too low. Readings below 20mV/m

are not supposed to be trusted, but it does seem to give reproducible

readings down to about 10mV/m, if the temperature is constant.

Also, the X, Y Z component feature doesn't seem to work well,

and should not have been included.

It's a good device. Too bad it's not as sensitive as the old

ia HF-detektor (which was not well put together and is

no longer available... I've also heard ia is phasing out

their support for it, so if you have one under warranty that

needs repair, don't delay).

Bill

On Fri, Apr 23, 2010 at 8:08 AM, lessemf.com <lessemf@...> wrote:

>

>

> Brand: TES Model No.: TES92

> I believe for HF

> Measures: 50Mhz-3.5Ghz in a variety of units:mV/m , V/m , ìA/m , mA/m ,

> ìW/m² , mW/m² , ìW/cm².

>

> I have had trouble with it ever since I bought it. I don't understand it.

> In

> these measurements, what are the " safety levels " ?

> Kris

>

> Hello Kris,

>

> What kind of trouble have you had? We might be able to assist you.

> We recommend using the mV/m units. It is the unit the meter is actually

> measuring (electric field). The other units are calculated (by the meter)

> from the mV/m. Also, it is a nice sensitive unit.

>

> the formula for converting is this:

>

> mW/cm2 = (V/m)2 / 3770

> [the 2's are exponents]

>

> Emil

>

>

> ________________________________

> From: charles <charles@... <charles%40milieuziektes.be>>

> <%40>

> Sent: Thu, April 22, 2010 11:33:30 AM

> Subject: Re: Re: RADAR HELP!

>

> What kind of electrosmog meter ?

>

> Brand?

> Type?

> LF or HF ?

>

> Greetings,

> Claessens

> member Verband Baubiologie

> www.milieuziektes.nl

> www.milieuziektes.be

> www.hetbitje.nl

> checked by Norton

>

> Re: Re: RADAR HELP!

>

> >

> > Radar and it's frequencies.

> > I do not have a meter that will measure this for me. I have an

> > electrosmog meter. Never does it read while they are flying. Does that

> > mean the radar is too high for it to read? I have never understood that

> > meter and have had trouble with it since I bought it last year. :(

> >

> >

>

> ------------------------------------

>

>

Guest guest
Posted

Thank you so much . I appreciate your educating me on this meter. I

will print this and keep it with the meter. I kinda wondered and figured that

the Radar was measuring above what this meter could handle.

Kris

________________________________

From: charles <charles@...>

Sent: Fri, April 23, 2010 2:20:33 AM

Subject: Re: Re: RADAR HELP!

You should use the unit μW/m².

If yoy do have a damaged immune system, you may become electrosensitive

between 200 and 2.000 μW/m².

When you have become electrosensitive, it is possible that you may have

reactions at less than 1 μW/m².

Normally, aircraft radar lies over you max of 3.5 GHz, so you cannot measure

them.

Greetings,

Claessens

member Verband Baubiologie

www.milieuziektes.nl

www.milieuziektes.be

www.hetbitje.nl

checked by Norton

Re: Re: RADAR HELP!

>

> Radar and it's frequencies.

> I do not have a meter that will measure this for me. I have an

> electrosmog meter. Never does it read while they are flying. Does that

> mean the radar is too high for it to read? I have never understood that

> meter and have had trouble with it since I bought it last year. :(

>

>

------------------------------------

Join the conversation

You are posting as a guest. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...