Jump to content
RemedySpot.com

Re: bacteria testing for MORs...

Rate this topic


Recommended Posts

Guest guest
Posted

Hi Dave:Thank you for this summary of your excellent research. This is real Rife research! Since you couldn't demonstrate the Rife effect with E. Coli bacteria, which is pretty much the 'gold standard' as far as demonstration test organisms go, I don't think there's any valid reason to suppose that any of the other audio frequencies for organisms are doing "the business" either.Regards,--- Dave Felt wrote:, all ...

In my tests, I used all the frequencies I could find for e. coli

bacteria. Using a plasma tube device at various distances from 0.5

meter to 10 meters, I was not able to slow the growth rate of the

bacteria, which were incubated in between culture density tests. A dual

beam spectrophotometer was used to do the density tests every 30

minutes after exposure to the plasma lamp - that initial exposure would

run from 30 minutes to about 80 minutes. In many, many tests, three

cultures exhibited a rapid die-off in growth rate, however those three

tests were never repeatable, even when started the same day with the

same machine, identical frequencies, and identical culture feed stock.

Each culture test would run typically 4 fours. Bacteria e.coli doubles

in density approximately every 22 minutes at 38 or 39 degrees C, so it

was pretty easy to measure the growing cultures, and after about an

hour (two sessions in the incubator) the cultures were visibly growing.

Of note was that e.coli actually prefers 40 or 41 degrees for optimal

growth, but even up to 55 degrees they were growing.

Additionally, the samples which were closest to the plasma lamp

(Bare-Rife used for these tests) grew faster, almost certainly from the

slight amount of heat entering the culture tubes from the lamp.

The various tests I've seen with pond animals were mostly done with

direct electrical stimulation, not with remote application such as

plasma lamps. Additionally, there is a huge world of difference between

pond animals and bacteria, so any comparison is kind of like really

large pumpkins and cherries, no real comparison at all.

In conclusion, I'm not certain that what we're seeing in our work are

actual MORs, it may be some form of immune system boost, or cell

apoptosis (death) somehow kicked off by the frequency energy.

Dave Felt

Guest guest
Posted

Hi Ken:It's not that we can't duplicate Rife's work, it's that we haven't. There are many reasons for this that I won't go into here. And no, we haven't reverse engineered his machines. We would need to have possession of his machines in order to reverse engineer them. What we have done is learned a lot more about the real world requirements for producing a machine that can run the frequencies that we have from the documents. It appears that there is still something missing.Regards,--- Ken Uzzell wrote:Hi Dave, and members,

Well then, it is becoming apparent we can't duplicate Dr. Rife's work, so we are unable to verify his claims as being true.

We have reverse engineered his machines, and have come up with new transmission frequencies that weren't available before.

<snip>

Guest guest
Posted

Hi Ken:In the tests that they did on this matter, they couldn't detect any magnetism coming from the tube.Regards,--- Ken Uzzell wrote:<snip> Could it be the electronics of his time produced stronger pulsed magnetic fields than what our modern day instruments are doing ?

<snip>Could it be Dr. Rife had a much larger gauss component in his transmissions, and this is what we are missing ?

<snip>

Guest guest
Posted

, all..

Last year I stared doing another set of tests using a microscope, video

camera and recorder, and sweeping a slow rate frequency generator

through the bands with a high power audio amplifier driving an EMEM

coil and plasma lamp - blew up the amplifier. Blew it up twice,

actually, smoke and sparks!! I'm almost ready to do it again, with a

different and better protected amplifier, but the time schedules just

aren't working for now for doing the tests.. Maybe this summer. The

spectrophotometer and culture tests would take 4 to 5 hours per test,

so I was going to see if I could determine frequencies by watching the

videotape, which had time and frequency also embedded on the tape, and

watching for frequencies which seemed to disturb the e.coli. Later..

-Dave

Ringas wrote:

Hi Dave:

Thank you for this summary of your excellent research. This is real

Rife research! Since you couldn't demonstrate the Rife effect with E.

Coli bacteria, which is pretty much the 'gold standard' as far as

demonstration test organisms go, I don't think there's any valid reason

to suppose that any of the other audio frequencies for organisms are

doing "the business" either.

Regards,

--- Dave Felt wrote:

,

all ...

In my tests, I used all the frequencies I could find for e. coli

bacteria. Using a plasma tube device at various distances from 0.5

meter to 10 meters, I was not able to slow the growth rate of the

bacteria, which were incubated in between culture density tests. A dual

beam spectrophotometer was used to do the density tests every 30

minutes after exposure to the plasma lamp - that initial exposure would

run from 30 minutes to about 80 minutes. In many, many tests, three

cultures exhibited a rapid die-off in growth rate, however those three

tests were never repeatable, even when started the same day with the

same machine, identical frequencies, and identical culture feed stock.

Each culture test would run typically 4 fours. Bacteria e.coli doubles

in density approximately every 22 minutes at 38 or 39 degrees C, so it

was pretty easy to measure the growing cultures, and after about an

hour (two sessions in the incubator) the cultures were visibly growing.

Of note was that e.coli actually prefers 40 or 41 degrees for optimal

growth, but even up to 55 degrees they were growing.

Additionally, the samples which were closest to the plasma lamp

(Bare-Rife used for these tests) grew faster, almost certainly from the

slight amount of heat entering the culture tubes from the lamp.

The various tests I've seen with pond animals were mostly done with

direct electrical stimulation, not with remote application such as

plasma lamps. Additionally, there is a huge world of difference between

pond animals and bacteria, so any comparison is kind of like really

large pumpkins and cherries, no real comparison at all.

In conclusion, I'm not certain that what we're seeing in our work are

actual MORs, it may be some form of immune system boost, or cell

apoptosis (death) somehow kicked off by the frequency energy.

Dave Felt

Guest guest
Posted

Part of the problem I belive is that most people are NOT trying to duplicate

what Rife did, they are duplicating what Crane did.

Perhaps we will never know what Rife really did, but we now know

about the Gruner circuit and also something about a actual Beamray machine. The

Beamray machines worked,therefore more effort should be directed towards that

technology,which boils down to heterodyning.

Beamray

> >

> > , all ...

> >

> > In my tests, I used all the frequencies I could find for e. coli

> > bacteria. Using a plasma tube device at various distances from 0.5

> > meter to 10 meters, I was not able to slow the growth rate of the

> > bacteria, which were incubated in between culture density tests. A

> > dual beam spectrophotometer was used to do the density tests every

> > 30 minutes after exposure to the plasma lamp - that initial

> > exposure would run from 30 minutes to about 80 minutes. In many,

> > many tests, three cultures exhibited a rapid die-off in growth

> > rate, however those three tests were never repeatable, even when

> > started the same day with the same machine, identical frequencies,

> > and identical culture feed stock. Each culture test would run

> > typically 4 fours. Bacteria e.coli doubles in density

> > approximately every 22 minutes at 38 or 39 degrees C, so it was

> > pretty easy to measure the growing cultures, and after about an

> > hour (two sessions in the incubator) the cultures were visibly

> > growing. Of note was that e.coli actually prefers 40 or 41 degrees

> > for optimal growth, but even up to 55 degrees they were growing.

> >

> > Additionally, the samples which were closest to the plasma lamp

> > (Bare-Rife used for these tests) grew faster, almost certainly

> > from the slight amount of heat entering the culture tubes from the

> > lamp.

> >

> > The various tests I've seen with pond animals were mostly done

> > with direct electrical stimulation, not with remote application

> > such as plasma lamps. Additionally, there is a huge world of

> > difference between pond animals and bacteria, so any comparison is

> > kind of like really large pumpkins and cherries, no real

> > comparison at all.

> >

> > In conclusion, I'm not certain that what we're seeing in our work

> > are actual MORs, it may be some form of immune system boost, or

> > cell apoptosis (death) somehow kicked off by the frequency energy.

> >

> > Dave Felt

> >>

> >

> >

>

Guest guest
Posted

--- beamray53 wrote:

> Part of the problem I belive is that

> most people are NOT trying to duplicate what Rife did, they

> are duplicating what Crane did.

> Perhaps we will never know what Rife really did, but we now

> know

> about the Gruner circuit and also something about a actual

> Beamray machine. The Beamray machines worked,therefore more

> effort should be directed towards that technology,which

> boils down to heterodyning.

> Beamray

It appears that there is still some misunderstanding regarding the work that was

done on the so-called Gruner circuit. As drawn, the circuit is unworkable.

There are no frequency tuning components, either on the RF oscillator or the

audio section. This may be due to it being incompletely or inadequately drawn.

Jim s' ingenious interpretation of the schematic was in the attempt to not

only make it a workable circuit, but also to be able to produce the original

Rife frequencies. We don't _know_ that this is actually how the original

machines worked. All we know is that Jim's solution is workable in the real

world. It has not yet been demonstrated to produce the Rife effect, so it is

premature to conclude that it " boils down to heterodyning " .

Regards,

Guest guest
Posted

In a word, no. The only figures I've seen mentioned is the input power, and also a current figure which would have been for the tubes in the machine.Regards,--- Ken Uzzell wrote:Hi ,

Is there any information on the signal transmissions ? I.E. RF levels, E Field levels?

Guest guest
Posted

Hi Dave,The Rife-Bare machine doesn't use a carrier frequency, does it?Randy

 

Hi Dave:Thank you for this summary of your excellent research.  This is real Rife research!  Since you couldn't demonstrate the Rife effect with E. Coli bacteria, which is pretty much the 'gold standard' as far as demonstration test organisms go, I don't think there's any valid reason to suppose that any of the other audio frequencies for organisms are doing " the business " either.

Regards,--- Dave Felt wrote:, all ...

In my tests, I used all the frequencies I could find for e. coli

bacteria. Using a plasma tube device at various distances from 0.5

meter to 10 meters, I was not able to slow the growth rate of the

bacteria, which were incubated in between culture density tests. A dual

beam spectrophotometer was used to do the density tests every 30

minutes after exposure to the plasma lamp - that initial exposure would

run from 30 minutes to about 80 minutes.  In many, many tests, three

cultures exhibited a rapid die-off in growth rate, however those three

tests were never repeatable, even when started the same day with the

same machine, identical frequencies, and identical culture feed stock. 

Each culture test would run typically 4 fours. Bacteria e.coli doubles

in density approximately every 22 minutes at 38 or 39 degrees C, so it

was pretty easy to measure the growing cultures, and after about an

hour (two sessions in the incubator) the cultures were visibly growing.

Of note was that e.coli actually prefers 40 or 41 degrees for optimal

growth, but even up to 55 degrees they were  growing.

Additionally, the samples which were closest to the plasma lamp

(Bare-Rife used for these tests) grew faster, almost certainly from the

slight amount of heat entering the culture tubes from the lamp.

The various tests I've seen with pond animals were mostly done with

direct electrical stimulation, not with remote application such as

plasma lamps. Additionally, there is a huge world of difference between

pond animals and bacteria, so any comparison is kind of like really

large pumpkins and cherries, no real comparison at all.

In conclusion, I'm not certain that what we're seeing in our work are

actual MORs, it may be some form of immune system boost, or cell

apoptosis (death) somehow kicked off by the frequency energy.

Dave Felt

Guest guest
Posted

: It does not really matter if the Gruner circuit is drawn correctly or

not. We do know that Dr's Couche and Tully's Beamray

machines worked to provide cures. We also know from Jeff's comments on the Rife

forum that an actual Beamray machine used heterodyning.

Whether it used RF to RF as suggestedd in the Gruner circuit, or audio to RF

heterodying as in the actual machine it still is a heterodyned device.

Perhaps Jeff will commment.

Beamray

>

> > Part of the problem I belive is that

> > most people are NOT trying to duplicate what Rife did, they

> > are duplicating what Crane did.

> > Perhaps we will never know what Rife really did, but we now

> > know

> > about the Gruner circuit and also something about a actual

> > Beamray machine. The Beamray machines worked,therefore more

> > effort should be directed towards that technology,which

> > boils down to heterodyning.

> > Beamray

>

>

> It appears that there is still some misunderstanding regarding the work that

was done on the so-called Gruner circuit. As drawn, the circuit is unworkable.

There are no frequency tuning components, either on the RF oscillator or the

audio section. This may be due to it being incompletely or inadequately drawn.

Jim s' ingenious interpretation of the schematic was in the attempt to not

only make it a workable circuit, but also to be able to produce the original

Rife frequencies. We don't _know_ that this is actually how the original

machines worked. All we know is that Jim's solution is workable in the real

world. It has not yet been demonstrated to produce the Rife effect, so it is

premature to conclude that it " boils down to heterodyning " .

>

> Regards,

>

>

>

>

Guest guest
Posted

Hi ,

Is there any information on the signal transmissions ? I.E. RF levels, E Field levels?

Strange to have a plasma globe ignited will oscillating charges and no magnetic component in the transmission.

Sincerely,

Ken Uzzellhttp://heal-me.com.auHealMe FoundationA New Humanity Associate

Re: bacteria testing for MORs...

Hi Ken:In the tests that they did on this matter, they couldn't detect any magnetism coming from the tube.Regards,--- Ken Uzzell wrote:

<snip>

Could it be the electronics of his time produced stronger pulsed magnetic fields than what our modern day instruments are doing ?<snip>

Could it be Dr. Rife had a much larger gauss component in his transmissions, and this is what we are missing ?

<snip>

Guest guest
Posted

--- beamray53 wrote:

> : It does not really matter if

> the Gruner circuit is drawn correctly or not. We do know

> that Dr's Couche and Tully's Beamray

> machines worked to provide cures.  We also know from

> Jeff's comments on the Rife forum that an actual Beamray

> machine used heterodyning.

> Whether it used RF to RF as suggestedd in the Gruner

> circuit, or audio to RF heterodying as in the actual machine

> it still is a heterodyned device. 

> Perhaps Jeff will commment.

Perhaps I missed that, but I don't recall Jeff saying this. Can you give a link

to his post? There is still a lot that we don't know about the original

machines. I don't think there is any hard evidence to make the conclusion that

heterodyning is " the key " . Of course the only real way to find out is to try it

and see if it " does the business " .

Regards,

Guest guest
Posted

No.

But you can run it using heterodyned audio frequencies,whether this method would

kill bacteria needs to be tested,or at least reported as tested.

If the desired frequency is 727Hz you could run 10000Hz and 9273Hz at the same

time using sine waves, of course you need two frequency generators,or one that

will output two sine frequencies at the same time. You could do this with square

waves but the periods need to overlap,they would have to start just about

exactly at the same time.

It seems to me that using square waves is more difficult as opposed to sine

waves.

You can also run it this way, using a 90 degree phase delay line on a split

carrier,which allows the use of a single input frequency that interferes with

itself.

http://www.rife1.com

I might add that heterodyning is a method to achieve interference and or

standing waves,which I believe is the Rife effect.

As I said before don't know whether the frequencies need to be in the RF range,

audio or ultrasonic range. The historical documents on the

#4 instrument would lead one to believe that the necessary frequencies are above

audio and ultrasonic.

Beamray

>

> Dear Beamray,

>

> Looking in a dictionary it says ...

>

> " Heterodyn

> Having alternating currents of two different frequencies that are combined

> to produce two new frequencies, the sum and difference of the original

> frequencies, either of which may be used in radio or television receivers by

> proper tuning or filtering. "

>

> Would the B/R instrument be classified as a Heterodyned device with its RF

> signal modulated with the audio signal, or do the two frequencies have to be

> closer together ?

>

> Sincerely,

>

> Ken Uzzell

>

> Re: bacteria testing for MORs...

>

>

> > : It does not really matter if the Gruner circuit is drawn correctly

> > or not. We do know that Dr's Couche and Tully's Beamray

> > machines worked to provide cures. We also know from Jeff's comments on

> > the Rife forum that an actual Beamray machine used heterodyning.

> > Whether it used RF to RF as suggestedd in the Gruner circuit, or audio to

> > RF heterodying as in the actual machine it still is a heterodyned device.

> > Perhaps Jeff will commment.

> >

> > Beamray

> >

> >

>

Guest guest
Posted

I can make a few comments. All deductions on the heterodyning came from making

the Gruner Schematic functional as pointed out. This was a logical

deduction that Jim s came to after looking at that schematic. Jim and I

talked and I told him that I could test his deduction that the Gruner Beam Ray

instrument was a heterodyning instrument first by connecting an AZ-58 and an

Aubrey Scoon instrument together. This test was done using a spectrum analyzer

which showed that all of Dr. Rife's frequencies could easily be produced through

heterodyning. Since all we have is this schematic and no actual Beam Ray

instrument then this is the best that we can do. Do I believe that this is the

way that the Gruner machine really worked? Yes, but only having an original

machine will prove it.

We do have some photos of Beam Ray machines that strongly indicate that Jim

's deduction is correct. Dr. Couche sold one of his Beam Ray instruments to

Dr. Tully and we have a photo of it. The dial locations on Dr. Couche's machine

matches the machine found in the May 1938 newspaper photo of Dr. Rife and Philip

Hoyland. That photo shows an actual Beam Ray machine. Both of these photos show

that there were no band switches on either of these machines which show they

were not audio frequency machines. They both only had one dial and could produce

all of the M.O.Rs. Heterodyning is the only way that I know of that could have

made them work. One oscillator would have been fixed and the other would have

been variable. This is the reason for only one dial and no band switches. These

photos and what I have mentioned above is the reason that Jim 's deduction

of the Gruner schematic makes the most sense. It works in the real world because

both of us have built it. Those who read my paper will just have to make up

their own minds if they think we are correct.

All of this is important, but, I think the most important discovery made was the

gating circuit. This circuit's output of a damped wave audio frequency minus the

ring oscillations matches the output of the Rife Ray #4 scope tracings shown in

the Rife Lab film. This is compelling evidence that gating is necessary in order

to produce the Rife effect. From the Rife Ray #4 documents we know that it had

two oscillators that could be set on any specific frequency they desired to use.

Heterodyning was produced by this machine as a by-product when they output two

frequencies at the same time but heterodyning was not used to produce the

M.O.Rs. The proof of this is the fact that the oscillators were tuned to the

M.O.R. frequency that they wanted. It also had band switches that allowed them

to pick the various frequency ranges. Because of these Rife Ray #4 documents, I

think it would be better to build an instrument that will output the specific

frequencies of the M.O.Rs and then test it to see what results are achieved.

Over the past few weeks I have been working on an instrument that will allow me

to set it on whatever M.O.R. I want to use without using heterodyning. This

requires winding large tank coils in order to get the lower frequency ranges. I

now have an instrument that will produce frequencies through a ray tube between

700,000 hertz to 365,000 hertz. I am going to wind an even larger coil so that I

can get more power out of the tube in order to make it work a little better. The

goal is to use it on some B-coli later this spring and see if it will produce

the desired effect. This instrument is using the old vacuum tubes that were used

in the old Rife equipment.

Jeff

> >

> > > Part of the problem I belive is that

> > > most people are NOT trying to duplicate what Rife did, they

> > > are duplicating what Crane did.

> > > Perhaps we will never know what Rife really did, but we now

> > > know

> > > about the Gruner circuit and also something about a actual

> > > Beamray machine. The Beamray machines worked,therefore more

> > > effort should be directed towards that technology,which

> > > boils down to heterodyning.

> > > Beamray

> >

> >

> > It appears that there is still some misunderstanding regarding the work that

was done on the so-called Gruner circuit. As drawn, the circuit is unworkable.

There are no frequency tuning components, either on the RF oscillator or the

audio section. This may be due to it being incompletely or inadequately drawn.

Jim s' ingenious interpretation of the schematic was in the attempt to not

only make it a workable circuit, but also to be able to produce the original

Rife frequencies. We don't _know_ that this is actually how the original

machines worked. All we know is that Jim's solution is workable in the real

world. It has not yet been demonstrated to produce the Rife effect, so it is

premature to conclude that it " boils down to heterodyning " .

> >

> > Regards,

> >

> >

> >

> >

>

Guest guest
Posted

I can make a few comments. All deductions on the heterodyning came from making

the Gruner Schematic functional as pointed out. This was a logical

deduction that Jim s came to after looking at that schematic. Jim and I

talked and I told him that I could test his deduction that the Gruner Beam Ray

instrument was a heterodyning instrument first by connecting an AZ-58 and an

Aubrey Scoon instrument together. This test was done using a spectrum analyzer

which showed that all of Dr. Rife's frequencies could easily be produced through

heterodyning. Since all we have is this schematic and no actual Beam Ray

instrument then this is the best that we can do. Do I believe that this is the

way that the Gruner machine really worked? Yes, but only having an original

machine will prove it.

We do have some photos of Beam Ray machines that strongly indicate that Jim

's deduction is correct. Dr. Couche sold one of his Beam Ray instruments to

Dr. Tully and we have a photo of it. The dial locations on Dr. Couche's machine

matches the machine found in the May 1938 newspaper photo of Dr. Rife and Philip

Hoyland. That photo shows an actual Beam Ray machine. Both of these photos show

that there were no band switches on either of these machines which show they

were not audio frequency machines. They both only had one dial and could produce

all of the M.O.Rs. Heterodyning is the only way that I know of that could have

made them work. One oscillator would have been fixed and the other would have

been variable. This is the reason for only one dial and no band switches. These

photos and what I have mentioned above is the reason that Jim 's deduction

of the Gruner schematic makes the most sense. It works in the real world because

both of us have built it. Those who read my paper will just have to make up

their own minds if they think we are correct.

All of this is important, but, I think the most important discovery made was the

gating circuit. This circuit's output of a damped wave audio frequency minus the

ring oscillations matches the output of the Rife Ray #4 scope tracings shown in

the Rife Lab film. This is compelling evidence that gating is necessary in order

to produce the Rife effect. From the Rife Ray #4 documents we know that it had

two oscillators that could be set on any specific frequency they desired to use.

Heterodyning was produced by this machine as a by-product when they output two

frequencies at the same time but heterodyning was not used to produce the

M.O.Rs. The proof of this is the fact that the oscillators were tuned to the

M.O.R. frequency that they wanted. It also had band switches that allowed them

to pick the various frequency ranges. Because of these Rife Ray #4 documents, I

think it would be better to build an instrument that will output the specific

frequencies of the M.O.Rs and then test it to see what results are achieved.

Over the past few weeks I have been working on an instrument that will allow me

to set it on whatever M.O.R. I want to use without using heterodyning. This

requires winding large tank coils in order to get the lower frequency ranges. I

now have an instrument that will produce frequencies through a ray tube between

700,000 hertz to 365,000 hertz. I am going to wind an even larger coil so that I

can get more power out of the tube in order to make it work a little better. The

goal is to use it on some B-coli later this spring and see if it will produce

the desired effect. This instrument is using the old vacuum tubes that were used

in the old Rife equipment.

Jeff

> >

> > > Part of the problem I belive is that

> > > most people are NOT trying to duplicate what Rife did, they

> > > are duplicating what Crane did.

> > > Perhaps we will never know what Rife really did, but we now

> > > know

> > > about the Gruner circuit and also something about a actual

> > > Beamray machine. The Beamray machines worked,therefore more

> > > effort should be directed towards that technology,which

> > > boils down to heterodyning.

> > > Beamray

> >

> >

> > It appears that there is still some misunderstanding regarding the work that

was done on the so-called Gruner circuit. As drawn, the circuit is unworkable.

There are no frequency tuning components, either on the RF oscillator or the

audio section. This may be due to it being incompletely or inadequately drawn.

Jim s' ingenious interpretation of the schematic was in the attempt to not

only make it a workable circuit, but also to be able to produce the original

Rife frequencies. We don't _know_ that this is actually how the original

machines worked. All we know is that Jim's solution is workable in the real

world. It has not yet been demonstrated to produce the Rife effect, so it is

premature to conclude that it " boils down to heterodyning " .

> >

> > Regards,

> >

> >

> >

> >

>

Guest guest
Posted

Beamray

I can make a few comments. All deductions on the heterodyning came from making

the Gruner Schematic functional as pointed out. This was a logical

deduction that Jim s came to after looking at that schematic. Jim and I

talked and I told him that I could test his deduction that the Gruner Beam Ray

instrument was a heterodyning instrument first by connecting an AZ-58 and an

Aubrey Scoon instrument together. This test was done using a spectrum analyzer

which showed that all of Dr. Rife's frequencies could easily be produced through

heterodyning. Since all we have is this schematic and no actual Beam Ray

instrument then this is the best that we can do. Do I believe that this is the

way that the Gruner machine really worked? Yes, but only having an original

machine will prove it.

We do have some photos of Beam Ray machines that strongly indicate that Jim

's deduction is correct. Dr. Couche sold one of his Beam Ray instruments to

Dr. Tully and we have a photo of it. The dial locations on Dr. Couche's machine

matches the machine found in the May 1938 newspaper photo of Dr. Rife and Philip

Hoyland. That photo shows an actual Beam Ray machine. Both of these photos show

that there were no band switches on either of these machines which show they

were not audio frequency machines. They both only had one dial and could produce

all of the M.O.Rs. Heterodyning is the only way that I know of that could have

made them work. One oscillator would have been fixed and the other would have

been variable. This is the reason for only one dial and no band switches. These

photos and what I have mentioned above is the reason that Jim 's deduction

of the Gruner schematic makes the most sense. It works in the real world because

both of us have built it. Those who read my paper will just have to make up

their own minds if they think we are correct.

All of this is important, but, I think the most important discovery made was the

gating circuit. This circuit's output of a damped wave audio frequency minus the

ring oscillations matches the output of the Rife Ray #4 scope tracings shown in

the Rife Lab film. This is compelling evidence that gating is necessary in order

to produce the Rife effect. From the Rife Ray #4 documents we know that it had

two oscillators that could be set on any specific frequency they desired to use.

Heterodyning was produced by this machine as a by-product when they output two

frequencies at the same time but heterodyning was not used to produce the

M.O.Rs. The proof of this is the fact that the oscillators were tuned to the

M.O.R. frequency that they wanted. It also had band switches that allowed them

to pick the various frequency ranges. Because of these Rife Ray #4 documents, I

think it would be better to build an instrument that will output the specific

frequencies of the M.O.Rs and then test it to see what results are achieved.

Over the past few weeks I have been working on an instrument that will allow me

to set it on whatever M.O.R. I want to use without using heterodyning. This

requires winding large tank coils in order to get the lower frequency ranges. I

now have an instrument that will produce frequencies through a ray tube between

700,000 hertz to 365,000 hertz. I am going to wind an even larger coil so that I

can get more power out of the tube in order to make it work a little better. The

goal is to use it on some B-coli later this spring and see if it will produce

the desired effect. This instrument is using the old vacuum tubes that were used

in the old Rife equipment.

Jeff

> >

> > > Part of the problem I belive is that

> > > most people are NOT trying to duplicate what Rife did, they

> > > are duplicating what Crane did.

> > > Perhaps we will never know what Rife really did, but we now

> > > know

> > > about the Gruner circuit and also something about a actual

> > > Beamray machine. The Beamray machines worked,therefore more

> > > effort should be directed towards that technology,which

> > > boils down to heterodyning.

> > > Beamray

> >

> >

> > It appears that there is still some misunderstanding regarding the work that

was done on the so-called Gruner circuit. As drawn, the circuit is unworkable.

There are no frequency tuning components, either on the RF oscillator or the

audio section. This may be due to it being incompletely or inadequately drawn.

Jim s' ingenious interpretation of the schematic was in the attempt to not

only make it a workable circuit, but also to be able to produce the original

Rife frequencies. We don't _know_ that this is actually how the original

machines worked. All we know is that Jim's solution is workable in the real

world. It has not yet been demonstrated to produce the Rife effect, so it is

premature to conclude that it " boils down to heterodyning " .

> >

> > Regards,

> >

> >

> >

> >

>

Guest guest
Posted

Jeff: I was under the impression that you had access to an actual Beamray

machine,which I believe heterodynes a RF carrier with audio range frequencies.

Is this not correct.

http://www.rifeforum.com/forum/showthread.php?t=2986

Beamray/Old Mike

> > >

> > > > Part of the problem I belive is that

> > > > most people are NOT trying to duplicate what Rife did, they

> > > > are duplicating what Crane did.

> > > > Perhaps we will never know what Rife really did, but we now

> > > > know

> > > > about the Gruner circuit and also something about a actual

> > > > Beamray machine. The Beamray machines worked,therefore more

> > > > effort should be directed towards that technology,which

> > > > boils down to heterodyning.

> > > > Beamray

> > >

> > >

> > > It appears that there is still some misunderstanding regarding the work

that was done on the so-called Gruner circuit. As drawn, the circuit is

unworkable. There are no frequency tuning components, either on the RF

oscillator or the audio section. This may be due to it being incompletely or

inadequately drawn. Jim s' ingenious interpretation of the schematic was

in the attempt to not only make it a workable circuit, but also to be able to

produce the original Rife frequencies. We don't _know_ that this is actually

how the original machines worked. All we know is that Jim's solution is

workable in the real world. It has not yet been demonstrated to produce the

Rife effect, so it is premature to conclude that it " boils down to

heterodyning " .

> > >

> > > Regards,

> > >

> > >

> > >

> > >

> >

>

Guest guest
Posted

My two cents worth here is that NO, the Bare-Rife is not a heterodyning

machine in the same sense that Rife's machine was. The audio frequencies

on the Bare-Rife are created directly using an audio generator, not by

the mixing of two RF frequencies.

Dave Felt

Ken Uzzell wrote:

> Dear Beamray,

>

> Looking in a dictionary it says ...

>

> " Heterodyn

> Having alternating currents of two different frequencies that are combined

> to produce two new frequencies, the sum and difference of the original

> frequencies, either of which may be used in radio or television receivers by

> proper tuning or filtering. "

>

> Would the B/R instrument be classified as a Heterodyned device with its RF

> signal modulated with the audio signal, or do the two frequencies have to be

> closer together ?

>

> Sincerely,

>

> Ken Uzzell

>

> Re: bacteria testing for MORs...

>

>

>

>> : It does not really matter if the Gruner circuit is drawn correctly

>> or not. We do know that Dr's Couche and Tully's Beamray

>> machines worked to provide cures. We also know from Jeff's comments on

>> the Rife forum that an actual Beamray machine used heterodyning.

>> Whether it used RF to RF as suggestedd in the Gruner circuit, or audio to

>> RF heterodying as in the actual machine it still is a heterodyned device.

>> Perhaps Jeff will commment.

>>

>> Beamray

>>

>>

>

Guest guest
Posted

--- Dave Felt wrote:

> My two  cents worth here is that

> NO, the Bare-Rife is not a heterodyning

> machine in the same sense that Rife's machine was. The

> audio frequencies

> on the Bare-Rife are created directly using an audio

> generator, not by

> the mixing of two RF frequencies.

Yes, but the sidebands that are in the output are the heterodyne products of the

audio and carrier. My opinion is that there would be no benefit to audio/RF

heterodyning. If you wanted a frequency that is the product of an audio/RF

heterodyne, you could just shift the RF by the appropriate amount and produce it

directly. I think the collective experience and evidence to date indicates that

all the various types of audio frequency devices " work " because they use the

same audio frequency pulse repetition rates. Until shown something substantial

to indicate otherwise, I think it's as simple as that.

Regards,

Guest guest
Posted

Beamray,

I do have an old audio modulated instrument in an original Beam Ray case. It has

a band switch for changing the range of audio frequencies along with an

amplitude dial. The case looks like the smaller Beam Ray case that is shown in

the May 1939 newspaper photo. In fact you can see where the original Beam Ray

plaque was once on the front of the instrument. This is the oldest audio

instrument that we have found. I have fixed the RF section and it has a fixed

carrier around 4 megahertz and it uses an audio oscillator generator just like

the AZ-58 and the Aubrey Scoon instruments. The audio section looks like it

produces sine wave audio frequencies not square wave. We will know more when it

is repaired. It does not produce the audio frequencies by the mixing of two RF

frequencies. This machine was either built by the Beam Ray Corporation as an

audio instrument or was modified from a heterodyning instrument to an audio

instrument by Verne . The inside of the case has a lot of holes and you

can see where various transformers used to be. But we have to remember that this

was in the 1930s during the depression and no one wasted anything so they may

have just used an old chassis that they had and then built the instrument. An

important clue was inside of this instrument and that is a photo of another

audio frequency instrument in a case that was the style of case that Dr.

Couche's machine was in. It has a band dial and amplitude dial on the front of

it like all of the audio instruments. So we now have two audio machines in both

styles of Beam Ray cases. I think the most important thing to consider is that

the Beam Ray Corporation may have built these instruments. If it did, then we

have instruments which show that Philip Hoyland built the first audio modulated

frequency instruments.

We know from the Beam Ray trial transcript that the Beam Ray Corporation was

building more than one type of instrument. We know from the documents that Dr.

Rife did not like one of those instruments and said it worked on harmonics.

Since a heterodyning instrument like the Gruner schematic could produce the high

M.O.Rs and the audio frequency instrument could not it is likely it was the

audio instrument that Dr. Rife did not like. The one thing we have to also

consider is by the 1950's Dr. Rife was working with Crane and Marsh

and was fully behind the building of these audio frequency instruments. In the

Marsh documents that we have Dr. Rife considered this AZ-58 instrument his

instrument and both Crane and Marsh recognized this fact. Also, the audio

instrument had a plaque on the front of it with Dr. Rife's name on it.

We may never know the whole truth but Dr. Rife had a great deal to do with the

audio frequency instrument.

Jeff

> > > >

> > > > > Part of the problem I belive is that

> > > > > most people are NOT trying to duplicate what Rife did, they

> > > > > are duplicating what Crane did.

> > > > > Perhaps we will never know what Rife really did, but we now

> > > > > know

> > > > > about the Gruner circuit and also something about a actual

> > > > > Beamray machine. The Beamray machines worked,therefore more

> > > > > effort should be directed towards that technology,which

> > > > > boils down to heterodyning.

> > > > > Beamray

> > > >

> > > >

> > > > It appears that there is still some misunderstanding regarding the work

that was done on the so-called Gruner circuit. As drawn, the circuit is

unworkable. There are no frequency tuning components, either on the RF

oscillator or the audio section. This may be due to it being incompletely or

inadequately drawn. Jim s' ingenious interpretation of the schematic was

in the attempt to not only make it a workable circuit, but also to be able to

produce the original Rife frequencies. We don't _know_ that this is actually

how the original machines worked. All we know is that Jim's solution is

workable in the real world. It has not yet been demonstrated to produce the

Rife effect, so it is premature to conclude that it " boils down to

heterodyning " .

> > > >

> > > > Regards,

> > > >

> > > >

> > > >

> > > >

> > >

> >

>

Guest guest
Posted

Dear Beamray,

Looking in a dictionary it says ...

" Heterodyn

Having alternating currents of two different frequencies that are combined

to produce two new frequencies, the sum and difference of the original

frequencies, either of which may be used in radio or television receivers by

proper tuning or filtering. "

Would the B/R instrument be classified as a Heterodyned device with its RF

signal modulated with the audio signal, or do the two frequencies have to be

closer together ?

Sincerely,

Ken Uzzell

Re: bacteria testing for MORs...

> : It does not really matter if the Gruner circuit is drawn correctly

> or not. We do know that Dr's Couche and Tully's Beamray

> machines worked to provide cures. We also know from Jeff's comments on

> the Rife forum that an actual Beamray machine used heterodyning.

> Whether it used RF to RF as suggestedd in the Gruner circuit, or audio to

> RF heterodying as in the actual machine it still is a heterodyned device.

> Perhaps Jeff will commment.

>

> Beamray

>

>

Guest guest
Posted

Jeff: Thanks for the clarification,quite a mystery to figure out.

Another thought on the Beamray instrument with the sweep switch.

Could it not be possible that Hoyland used the sweep function in his efforts to

hide the frequencies. By sweeping the frequencies over the range of all MOR's no

one would be able to figure out the specific MOR for any give pathogen.

Is there any indication of a sweep circuit in the Gruner schematic.

Beamray/Mike

> > > > >

> > > > > > Part of the problem I belive is that

> > > > > > most people are NOT trying to duplicate what Rife did, they

> > > > > > are duplicating what Crane did.

> > > > > > Perhaps we will never know what Rife really did, but we now

> > > > > > know

> > > > > > about the Gruner circuit and also something about a actual

> > > > > > Beamray machine. The Beamray machines worked,therefore more

> > > > > > effort should be directed towards that technology,which

> > > > > > boils down to heterodyning.

> > > > > > Beamray

> > > > >

> > > > >

> > > > > It appears that there is still some misunderstanding regarding the

work that was done on the so-called Gruner circuit. As drawn, the circuit is

unworkable. There are no frequency tuning components, either on the RF

oscillator or the audio section. This may be due to it being incompletely or

inadequately drawn. Jim s' ingenious interpretation of the schematic was

in the attempt to not only make it a workable circuit, but also to be able to

produce the original Rife frequencies. We don't _know_ that this is actually

how the original machines worked. All we know is that Jim's solution is

workable in the real world. It has not yet been demonstrated to produce the

Rife effect, so it is premature to conclude that it " boils down to

heterodyning " .

> > > > >

> > > > > Regards,

> > > > >

> > > > >

> > > > >

> > > > >

> > > >

> > >

> >

>

Guest guest
Posted

Hi Jeff / ,

I'd like to step back just for a moment and ask for clarification about the

period of years involved in these instruments under discussion, and in your

long analysis paper. Specifically, is it from 1934 onward (i.e., from the

time Hoyland came on the scene)? Or does it include the years and

instruments prior to 1934, let's say the late 1920s through the first part

of 1934, during which Hoyland was not present and the instruments were not

yet called Beam Ray?

I could go to your paper and try to figure it out, but asking would be

easier and faster. :-)

Also, it's not clear to me what year the video was from, in which a waveform

was mentioned - this was in a post a few days ago.

Thank you!

Charlene Boehm

www.dnafrequencies.com

_____________________________________

> Beamray,

>

>

> I do have an old audio modulated instrument in an original Beam Ray case.

It has a band switch for changing the range of audio frequencies along with

an amplitude dial. The case looks like the smaller Beam Ray case that is

shown in the May 1939 newspaper photo. In fact you can see where the

original Beam Ray plaque was once on the front of the instrument. This is

the oldest audio instrument that we have found. I have fixed the RF section

and it has a fixed carrier around 4 megahertz and it uses an audio

oscillator generator just like the AZ-58 and the Aubrey Scoon instruments.

The audio section looks like it produces sine wave audio frequencies not

square wave. We will know more when it is repaired. It does not produce the

audio frequencies by the mixing of two RF frequencies. This machine was

either built by the Beam Ray Corporation as an audio instrument or was

modified from a heterodyning instrument to an audio instrument by Verne

. The inside of the case has a lot of holes and you can see where

various transformers used to be. But we have to remember that this was in

the 1930s during the depression and no one wasted anything so they may have

just used an old chassis that they had and then built the instrument. An

important clue was inside of this instrument and that is a photo of another

audio frequency instrument in a case that was the style of case that Dr.

Couche's machine was in. It has a band dial and amplitude dial on the front

of it like all of the audio instruments. So we now have two audio machines

in both styles of Beam Ray cases. I think the most important thing to

consider is that the Beam Ray Corporation may have built these instruments.

If it did, then we have instruments which show that Philip Hoyland built the

first audio modulated frequency instruments.

>

>

> We know from the Beam Ray trial transcript that the Beam Ray Corporation

was building more than one type of instrument. We know from the documents

that Dr. Rife did not like one of those instruments and said it worked on

harmonics. Since a heterodyning instrument like the Gruner schematic could

produce the high M.O.Rs and the audio frequency instrument could not it is

likely it was the audio instrument that Dr. Rife did not like. The one thing

we have to also consider is by the 1950's Dr. Rife was working with

Crane and Marsh and was fully behind the building of these audio

frequency instruments. In the Marsh documents that we have Dr. Rife

considered this AZ-58 instrument his instrument and both Crane and Marsh

recognized this fact. Also, the audio instrument had a plaque on the front

of it with Dr. Rife's name on it.

>

>

> We may never know the whole truth but Dr. Rife had a great deal to do with

the audio frequency instrument.

>

>

> Jeff

Guest guest
Posted

Mike,

Perhaps there is another reason that there was a sweep switch

? Frequency accuracy was critical, but with aging of the components,

variations in AC line voltage, and so on, frequencies could drift

some from the original calibrations. A sweep could easily accommodate

for induced inaccuracies.

Jim Bare

>Another thought on the Beamray instrument with the sweep switch.

>Could it not be possible that Hoyland used the sweep function in his

>efforts to hide the frequencies.

Guest guest
Posted

Hi Char:

The instruments we're talking about are the Beam Rays Corp. instruments that

were built after the 1935 #4 instrument. The only real details we have on the

previous instruments is that they used the Kennedy radios as oscillators. We

don't have any specifications on the amplifier or any other additional

components.

The lab film was compiled in 1936, but the footage was taken earlier. Other

than the #4 machine and the Abrams Oscilloclast at the end, we don't know what

machines all the waveforms were taken from.

Regards,

--- cb wrote:

> Hi Jeff / ,

>

> I'd like to step back just for a moment and ask for

> clarification about the

> period of years involved in these instruments under

> discussion, and in your

> long analysis paper.  Specifically, is it from 1934

> onward (i.e., from the

> time Hoyland came on the scene)?  Or does it include

> the years and

> instruments prior to 1934, let's say the late 1920s through

> the first part

> of 1934, during which Hoyland was not present and the

> instruments were not

> yet called Beam Ray?

>

> I could go to your paper and try to figure it out, but

> asking would be

> easier and faster.   :-)

> Also, it's not clear to me what year the video was from, in

> which a waveform

> was mentioned - this was in a post a few days ago.

Guest guest
Posted

Hello Charlene,

The paper covers from the early 1920s forward to the 1950s. The lab film was

made in the spring of 1936 for a conference that Dr. Rife was going to attend.

The Rife Ray #4 which was completed by the fall of 1935 is shown in the lab

film.

Jeff

>

> Hi Jeff / ,

>

> I'd like to step back just for a moment and ask for clarification about the

> period of years involved in these instruments under discussion, and in your

> long analysis paper. Specifically, is it from 1934 onward (i.e., from the

> time Hoyland came on the scene)? Or does it include the years and

> instruments prior to 1934, let's say the late 1920s through the first part

> of 1934, during which Hoyland was not present and the instruments were not

> yet called Beam Ray?

>

> I could go to your paper and try to figure it out, but asking would be

> easier and faster. :-)

> Also, it's not clear to me what year the video was from, in which a waveform

> was mentioned - this was in a post a few days ago.

>

> Thank you!

> Charlene Boehm

> www.dnafrequencies.com

> _____________________________________

>

>

> > Beamray,

> >

> >

> > I do have an old audio modulated instrument in an original Beam Ray case.

> It has a band switch for changing the range of audio frequencies along with

> an amplitude dial. The case looks like the smaller Beam Ray case that is

> shown in the May 1939 newspaper photo. In fact you can see where the

> original Beam Ray plaque was once on the front of the instrument. This is

> the oldest audio instrument that we have found. I have fixed the RF section

> and it has a fixed carrier around 4 megahertz and it uses an audio

> oscillator generator just like the AZ-58 and the Aubrey Scoon instruments.

> The audio section looks like it produces sine wave audio frequencies not

> square wave. We will know more when it is repaired. It does not produce the

> audio frequencies by the mixing of two RF frequencies. This machine was

> either built by the Beam Ray Corporation as an audio instrument or was

> modified from a heterodyning instrument to an audio instrument by Verne

> . The inside of the case has a lot of holes and you can see where

> various transformers used to be. But we have to remember that this was in

> the 1930s during the depression and no one wasted anything so they may have

> just used an old chassis that they had and then built the instrument. An

> important clue was inside of this instrument and that is a photo of another

> audio frequency instrument in a case that was the style of case that Dr.

> Couche's machine was in. It has a band dial and amplitude dial on the front

> of it like all of the audio instruments. So we now have two audio machines

> in both styles of Beam Ray cases. I think the most important thing to

> consider is that the Beam Ray Corporation may have built these instruments.

> If it did, then we have instruments which show that Philip Hoyland built the

> first audio modulated frequency instruments.

> >

> >

> > We know from the Beam Ray trial transcript that the Beam Ray Corporation

> was building more than one type of instrument. We know from the documents

> that Dr. Rife did not like one of those instruments and said it worked on

> harmonics. Since a heterodyning instrument like the Gruner schematic could

> produce the high M.O.Rs and the audio frequency instrument could not it is

> likely it was the audio instrument that Dr. Rife did not like. The one thing

> we have to also consider is by the 1950's Dr. Rife was working with

> Crane and Marsh and was fully behind the building of these audio

> frequency instruments. In the Marsh documents that we have Dr. Rife

> considered this AZ-58 instrument his instrument and both Crane and Marsh

> recognized this fact. Also, the audio instrument had a plaque on the front

> of it with Dr. Rife's name on it.

> >

> >

> > We may never know the whole truth but Dr. Rife had a great deal to do with

> the audio frequency instrument.

> >

> >

> > Jeff

>

Join the conversation

You are posting as a guest. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...