Guest guest Posted April 25, 2006 Report Share Posted April 25, 2006 Hi Doug, , our chief electonic engineerinig kind of guru says it makes for easier plasma ignition. He says that the copper wool is not " necessary " but just " nice " to have as he likes to " grease the skids " whenever possible. Okay, put your Phanatron in the cupboard and take your plasma globe: 1. Open the base of the glove and pull directly away from the base of the unit. 2. Cut off the high voltage wire going up out of the center of the base, cut it as low as you can to the base of the unit. 3. Drill a small hole in the side of the globe base and mount a banana plug female or just put a bolt to make a screw terminal. 4. Put a piece of HV wire (high dielectric insulated solid core wire) up the center of the tube and jam it's bared end into the steel wool. Fasten the other end to your banana terminal or bolt which will be your screw terminal. 5. Put the base back on because the weight it provides is nice. Just apply your HV to that terminal on the outside of the globe base. You are sendiing a direct (non-carrier) frequency to the wool which is the electrode and viola! There is no need to put a negative wire anywhere because the e-field will be much more powerful as the electrical discharges that comprise the field will seek home (Earth) and give you what you want. This is good for both contact and radiated frequency treatment. Yours, Dr. Ian MacLeod, Ph.D. Rollins, M.A., M.S. B.A., EE. polo wrote: What is the advantage of replacing and using copper wool over the steel wool in a plasma globe? thanks, doug ps. I am also using Bare's OM-1 transmitter and his 300 watt PEP amplifier. Quote Link to comment Share on other sites More sharing options...
Guest guest Posted April 25, 2006 Report Share Posted April 25, 2006 nnnn --------------------------------- How low will we go? Check out Yahoo! Messenger’s low PC-to-Phone call rates. Quote Link to comment Share on other sites More sharing options...
Guest guest Posted April 30, 2006 Report Share Posted April 30, 2006 Hi Ian, Have you looked into Wade's device. It uses a piezo element to generate ultrasonic vibrations applied directly to the surface of the skin. He indicates that it causes the pathogens to vibrate at their MOR freguency just like other magnetic or electrical contact devices do. He slowly sweeps over a wide range of frequencies during a 45 minute period. > Hi , > True:- > 1. Iron core(Laminations) is fine for low > audio. Ferrite for higher. > 2. You won't get a good squarewave from any transformer. > gesi > ================= > > > > Dr. Ian MacLeod, Ph.D., New Lhasa Research Facility, In search of the truth through relentless research and infinite patience. > > --------------------------------- > Talk is cheap. Use Yahoo! Messenger to make PC-to-Phone calls. Great rates starting at 1 & cent;/min. > > Quote Link to comment Share on other sites More sharing options...
Guest guest Posted April 30, 2006 Report Share Posted April 30, 2006 Yes, Realise that his Peizo element is identical in function to a resonating coil, or any coil type element in its use to carry frequencies. It is an excellent method for conveying frequencies to specific and limited areas. As far as sweeping over a wide range of frequencies ... I have no comment on this approach. Yours, Dr. Ian MacLeod, Ph.D. martin7730 wrote: Hi Ian, Have you looked into Wade's device. It uses a piezo element to generate ultrasonic vibrations applied directly to the surface of the skin. He indicates that it causes the pathogens to vibrate at their MOR freguency just like other magnetic or electrical contact devices do. He slowly sweeps over a wide range of frequencies during a 45 minute period. Dr. Ian MacLeod, Ph.D., New Lhasa Research Facility, In search of the truth through relentless research and infinite patience. --------------------------------- Yahoo! Messenger with Voice. Make PC-to-Phone Calls to the US (and 30+ countries) for 2¢/min or less. Quote Link to comment Share on other sites More sharing options...
Guest guest Posted April 30, 2006 Report Share Posted April 30, 2006 > Hi Ian, > > Have you looked into Wade's device. It uses a piezo element to > generate ultrasonic vibrations applied directly to the surface of the > skin. He indicates that it causes the pathogens to vibrate at their > MOR freguency just like other magnetic or electrical contact devices > do. He slowly sweeps over a wide range of frequencies during a 45 > minute period. > > > > Dr. Ian MacLeod, Ph.D., New Lhasa Research Facility, In search of the truth through relentless research and infinite patience. > > --------------------------------- > Yahoo! Messenger with Voice. Make PC-to-Phone Calls to the US (and 30+ countries) for 2¢/min or less. > > Quote Link to comment Share on other sites More sharing options...
Guest guest Posted April 30, 2006 Report Share Posted April 30, 2006 also proposed a new type of tube that might be better for rifing... http://educate-yourself.org/gw/gwriferaytubes26sep9.shtml If I ever get a plasma type machine again (which I might), then I might try it. The big disadvantage of 's machine is that it only treats a localized area... > > Hi Ian, > > > > Have you looked into Wade's device. It uses a piezo element to > > generate ultrasonic vibrations applied directly to the surface of > the > > skin. He indicates that it causes the pathogens to vibrate at their > > MOR freguency just like other magnetic or electrical contact > devices > > do. He slowly sweeps over a wide range of frequencies during a 45 > > minute period. > > > > > > > > Dr. Ian MacLeod, Ph.D., New Lhasa Research Facility, In search of > the truth through relentless research and infinite patience. > > > > --------------------------------- > > Yahoo! Messenger with Voice. Make PC-to-Phone Calls to the US (and > 30+ countries) for 2¢/min or less. > > > > Quote Link to comment Share on other sites More sharing options...
Guest guest Posted May 1, 2006 Report Share Posted May 1, 2006 , From our initial studies and our Vietnamese colleagues the results are identical. Yours, Dr. Ian MacLeod, Ph.D. martin7730 wrote: Ian The piezo generates mechanical vibrations, whereas the coil produces a magnetic field. Do you believe that producing mechanical vibrations via the piezo is much more efficient then use of a magnetic coil? Dr. Ian MacLeod, Ph.D., New Lhasa Research Facility, In search of the truth through relentless research and infinite patience. --------------------------------- Talk is cheap. Use Yahoo! Messenger to make PC-to-Phone calls. Great rates starting at 1 & cent;/min. Quote Link to comment Share on other sites More sharing options...
Guest guest Posted May 1, 2006 Report Share Posted May 1, 2006 Please remember this: Treatments of disease in bacterial and viral forms is often well-treated with plasma and tuned antenna treatment, but when it comes to specific area treatment and cellular regeneration ... direct contact treatment has some distinct advantages. There is a place for both methodologies, that is certain. Yours, Dr. Ian MacLeod, Ph.D. zenalpha wrote: also proposed a new type of tube that might be better for rifing... http://educate-yourself.org/gw/gwriferaytubes26sep9.shtml If I ever get a plasma type machine again (which I might), then I might try it. The big disadvantage of 's machine is that it only treats a localized area... > Ian > Dr. Ian MacLeod, Ph.D., New Lhasa Research Facility, In search of the truth through relentless research and infinite patience. --------------------------------- Love cheap thrills? Enjoy PC-to-Phone calls to 30+ countries for just 2¢/min with Yahoo! Messenger with Voice. Quote Link to comment Share on other sites More sharing options...
Guest guest Posted May 1, 2006 Report Share Posted May 1, 2006 Hi Ian, Have you found any particular voltage and current levels to optimise treatment when useing contact pads ? Have you found (in humans) that one method of attachment I.E. hands, is better than say feet, or direct attachment to the injured sight ? It's a great opportunity to be able to speak with people who have throughly researched this field. Trying to gleam all the secrets out of you ;-) LOL Regards, Ken Uzzell http://heal-me.com.au Frex - CHIamp Re: Re: RB tube losing power Please remember this: Treatments of disease in bacterial and viral forms is often well-treated with plasma and tuned antenna treatment, but when it comes to specific area treatment and cellular regeneration ... direct contact treatment has some distinct advantages. There is a place for both methodologies, that is certain. Yours, Dr. Ian MacLeod, Ph.D. zenalpha wrote: also proposed a new type of tube that might be better for rifing... http://educate-yourself.org/gw/gwriferaytubes26sep9.shtml If I ever get a plasma type machine again (which I might), then I might try it. The big disadvantage of 's machine is that it only treats a localized area... > Ian > Dr. Ian MacLeod, Ph.D., New Lhasa Research Facility, In search of the truth through relentless research and infinite patience. --------------------------------- Love cheap thrills? Enjoy PC-to-Phone calls to 30+ countries for just 2¢/min with Yahoo! Messenger with Voice. Quote Link to comment Share on other sites More sharing options...
Guest guest Posted May 1, 2006 Report Share Posted May 1, 2006 Excellent Questions, Hi Ken, here we go ... First of all, the greatest potential is realised when you are directly treating the injury site. We have had significant results when directly treating the area under effect, ie. a broken wrist. Now this brings to mind that we are dealing with three primary cases for treatment: 1. Viral Malady. 2. Bacterial Malady. 3. Trauma Malady. In the first 2 we treat similarly, and if there is a specific area influenced we use contact pads and directly treat that area. Treating the whole body with contact pads is done ... but far more infrequently as we have had so much success with the plasma and frequency tuned antennas. Amplitude: We usually find at an applied NLV (No Load Voltage) of 12-20v P.P. is ideal. Now, remember an addage we use, " It's not the power, but the precision " which tells us that with more exact frequency applications we achieve excellent results with as little as 1.25V applied NLV. This is with a clean sinusoidal waveform that is true to within (ideally) 5% accuracy of waveform and frequency. We have found that a variance of up to 10% will still allow fairly acceptable results but that the effectiveness curve is huge and anything beyond 10% rapidly diminishes in effectiveness to the point of worthlessness in a heartbeat! Typically we will attach the " + " electrode over the injury site and the " - " electrode to the left or right ankle. We will effect a regularly switching polarity so that the electrodes are electrically reversed frequently. When treating whole body we always go " + " Right Wrist, " - " Left Ankle and, again, use the frequent polarity switching protocol. Keep up the good work and the wonderful questions, Yours in Research and a Growing Friendship, Dr. Ian MacLeod, Ph,.D. Ken Uzzell wrote: Hi Ian, Have you found any particular voltage and current levels to optimise treatment when useing contact pads ? Have you found (in humans) that one method of attachment I.E. hands, is better than say feet, or direct attachment to the injured sight ? It's a great opportunity to be able to speak with people who have throughly researched this field. Trying to gleam all the secrets out of you ;-) LOL Regards, Ken Uzzell http://heal-me.com.au Frex - CHIamp Re: Re: RB tube losing power Please remember this: Treatments of disease in bacterial and viral forms is often well-treated with plasma and tuned antenna treatment, but when it comes to specific area treatment and cellular regeneration ... direct contact treatment has some distinct advantages. There is a place for both methodologies, that is certain. Yours, Dr. Ian MacLeod, Ph.D. zenalpha wrote: also proposed a new type of tube that might be better for rifing... http://educate-yourself.org/gw/gwriferaytubes26sep9.shtml If I ever get a plasma type machine again (which I might), then I might try it. The big disadvantage of 's machine is that it only treats a localized area... > Ian > Dr. Ian MacLeod, Ph.D., New Lhasa Research Facility, In search of the truth through relentless research and infinite patience. --------------------------------- Love cheap thrills? Enjoy PC-to-Phone calls to 30+ countries for just 2?min with Yahoo! Messenger with Voice. Quote Link to comment Share on other sites More sharing options...
Guest guest Posted May 2, 2006 Report Share Posted May 2, 2006 Correct me if I am wrong, but what you are describing below can be done with the unmodified output of a $200 function generator, and at far better than 10% distortion. Most will do 20Vpp without the kind of step-up transformer used in the Crane type devices. Even a free software generator and computer soundcard would give you a few volts. Aside from the exact sinewave frequencies, are there any criteria I am missing here. For example, how are you dealing with impedance matching between the pads and body? Do you really mean you have a positive and negative electrode, or do you have a positive and ground? Nielsen >Amplitude: We usually find at an applied NLV (No Load Voltage) of >12-20v P.P. is ideal. Now, remember an addage we use, " It's not the >power, but the precision " which tells us that with more exact >frequency applications we achieve excellent results with as little >as 1.25V applied NLV. This is with a clean sinusoidal waveform that >is true to within (ideally) 5% accuracy of waveform and frequency. Quote Link to comment Share on other sites More sharing options...
Guest guest Posted May 2, 2006 Report Share Posted May 2, 2006 Hi , You are essentially right on target. Remember that you are periodically reversing polarity of the electrodes as the specific frequency is being transmitted through them. Yes, an analogue frequency generator supplying a clean sine wave through the contact pads or coils will, indeed do a pretty good job. Remember that this is most effective, as described, on localised injury or malady and is more marginal when treating " whole body " conditions. Again, the correct frequency is important, very important, as a more precise frequency requires significantly less power. Exact sinusoidal frequency is critical to success! Be a sharpshooter, not a shotgunner. As far as impedance matching between the contact pads and the body; a simple resistance match is achieved through a variable load matching network, similar to an audio speaker impedance matching circuit (only variable) after having taken a reading of the subject's body which is not difficult at all. Yes , it is really that simple. So many people have gone so far overboard in their attempts to complicate the simple that it is fast confusing the " little man " and causing many good and valuable people to abandon the pursuit of an end in this quest. The constant discussion of " scalar waves " , " harmonic distortion " , etc., etc., etc., clouds a relatively simple science. Search for the mysterious " Rife Effect " is the greatest myth of them all and has done more to hurt this science than the FDA. I personally want to thank you for this forum, your inputs, and your allowing all views, even those which are ridiculously off-track, because through all the din there are the occasional pearls of knowledge that are well worth the work of harvesting them. Yours Always, Dr. Ian MacLeod, Ph.D. Nielsen wrote: Correct me if I am wrong, but what you are describing below can be done with the unmodified output of a $200 function generator, and at far better than 10% distortion. Most will do 20Vpp without the kind of step-up transformer used in the Crane type devices. Even a free software generator and computer soundcard would give you a few volts. Aside from the exact sinewave frequencies, are there any criteria I am missing here. For example, how are you dealing with impedance matching between the pads and body? Do you really mean you have a positive and negative electrode, or do you have a positive and ground? Nielsen Dr. Ian MacLeod, Ph.D., New Lhasa Research Facility, In search of the truth through relentless research and infinite patience. --------------------------------- Yahoo! Messenger with Voice. PC-to-Phone calls for ridiculously low rates. Quote Link to comment Share on other sites More sharing options...
Guest guest Posted May 2, 2006 Report Share Posted May 2, 2006 Hi Ian, What voltage level is your IM007 driving your globe. Today at Wallmart I just purchased an 8 " Electrostorm Globe and want to drive it with my stereo amp and step up transformer. As always I appreciate your time and dedication. > Correct me if I am wrong, but what you are describing below can be > done with the unmodified output of a $200 function generator, and at > far better than 10% distortion. Most will do 20Vpp without the kind > of step-up transformer used in the Crane type devices. Even a free > software generator and computer soundcard would give you a few volts. > > Aside from the exact sinewave frequencies, are there any criteria I > am missing here. For example, how are you dealing with impedance > matching between the pads and body? > > Do you really mean you have a positive and negative electrode, or do > you have a positive and ground? > > Nielsen > > Dr. Ian MacLeod, Ph.D., New Lhasa Research Facility, In search of the truth through relentless research and infinite patience. > > --------------------------------- > Yahoo! Messenger with Voice. PC-to-Phone calls for ridiculously low rates. > > Quote Link to comment Share on other sites More sharing options...
Guest guest Posted May 2, 2006 Report Share Posted May 2, 2006 Hi , Our IM007 produces about 1.20 - 24.5v. P.P. NLV (No Load Volts) depending on the frequency generated. We are running it's signal through an audio amplifier that is protected via Ground Fault Interruption protection and also grounded to true ground. Inside the amplifier are numerous redundant grounds and the amplifier itself has been tweeked for accurate reproduction of sinusoidal waveform and frequency. It is an analogue, Valve (Vacuum Tube) audio amplifier and is extremely accurate through the range of 10hz - 12.5Khz which is more than sufficient for our work. You may use a commercially available audio amplifier but I must add this caviat: PROTECT YOURSELF BY INSTALLING GFI AND TRUE GROUND PROTECTION TO THE AMPLIFIER AND ANY AND ALL EQUIPMENT THAT IS POWERED FROM MAINS ELECTRICITY! The ability to drive your lamp will depend on the output voltage and, to a lesser extent, available current from your amplifier. If you are using a transformer be aware that it will not reproduce a clean sine wave except in an extremely narrow range of frequencies (probably 40-70hz) unless it is specifically wound and loaded to the frequency you are using. A deformed sine wave begins to produce unwanted and unpredictable harmonics, not to mention that the coil itself is a transmitter of these harmonics, and you have no idea where you are " aiming " your frequencies (as there is no longer any specifific frequency but a smattering of harmonics) even if your coil is inside a Faraday Cage. We have modified a high voltage automobile " E-Core to Americans " flyback-style ignition coil (inside a grounded Faraday Cage) with a variable balancing coil so as to keep a clean sine wave at any frequency. At present it requires rebalancing each time we change frequencies significantly, but an automatic balancing system is not far off according to my guru, . Best of luck to you. Remember that the applied voltage to your tube will want to be at least 1500V so be careful! You can pull quite a nasty little jolt from these toys! Warmest Regards, Dr. Ian MacLeod, Ph.D. martin7730 wrote: Hi Ian, What voltage level is your IM007 driving your globe. Today at Wallmart I just purchased an 8 " Electrostorm Globe and want to drive it with my stereo amp and step up transformer. As always I appreciate your time and dedication. Dr. Ian MacLeod, Ph.D., New Lhasa Research Facility, In search of the truth through relentless research and infinite patience. --------------------------------- Get amazing travel prices for air and hotel in one click on Yahoo! FareChase Quote Link to comment Share on other sites More sharing options...
Guest guest Posted May 2, 2006 Report Share Posted May 2, 2006 And now I must ask an obvious question. The MHz frequencies of Rife's devices are sometimes assumed to match the physical wavelength of the virus. In actuality, they were probably a lower harmonic. The nominal mode of activity is therefore EM resonance. The modulating audio MOR was simultaneously emitted as an acoustic wave. These are two distinct and complimentary modalities, neither of which is apparently produced by the system you describe. Since audio wavelengths are too long to produce significant EM resonance within the body, and pads or coils do not emit acoustic waves, what mechanism of action are you suggesting? Nielsen > Again, the correct frequency is important, very important, as a > more precise frequency requires significantly less power. Exact > sinusoidal frequency is critical to success! Be a sharpshooter, > not a shotgunner. Quote Link to comment Share on other sites More sharing options...
Guest guest Posted May 2, 2006 Report Share Posted May 2, 2006 Hi Ian, I think the Rife Effect is very real, it's just understanding the physiology of what is happening, when indeed a Rife Effect does occur. The Rife Effect is just another way of saying, a miracle healing occurred. We just got lucky with a frequency, or a few of them, and the body discovered the resources to heal, extremely fast. To the fact that some people are even doubted if they were ill in the first place. This may be a function of the sine wave harmonic spectrum delivered to the body, or it might be achieved with sine waves alone, I have not tested out sine waves yet, still waiting :-) At times when these healings occur, as they can with physical therapy, drug therapy, and all other religious and spiritual disciplines, including people just having a holiday, and it seems to be a frequent experience of frequency therapy, then some subtle component of the body, or the body as a whole, did a complete illness reversal. What part of our body can change so dramatically, to produce this healing that is acceptable to medical science yet appears as a miracle has occurred ? Simple! The fascia can do a full unwind, and trauma release. I've been practising Myofascial Release Therapy ( PT style) for nearly 8 years, and I have witnessed many fascia unwindings. People heal very quickly, just what happens with the Rife Effect which I have also observed on occasions. Since Frex's release, numerus people have experienced these complete health turn around's from speakers in their hands, listening to audio tones, using that raspy and jittery square wave coming from a pc speaker via stereo amplifier. Not really acceptable to engineers of this therapy, but non the less, it has produced results. The only thing I have observed is the fact that the fascia has released its stress and trauma, and the body has the resources to heal, very quickly. This is easy to test by physical palpation into the body by a trained and experienced therapist. Our fascia is our structural body, that houses all organs, skeleton, and fluid pathways. It is functionally associated with every tissue in the body, brain and spine included. Recent discoveries have displayed a fascia sheath covers every cell giving it protection and structure. Just recently, a fascial skeletal structure was found to be in every cell of our body, giving structure, shape and cell protection and also contributing to the freedom of the cells components to properly function. Now I believe fascia is electromagnetic and electrostatic effected, otherwise contact pads and plasma transmitters wouldn't effect it. We can program it with our machines to release, and I bet we can program it to tighten-up, and become traumatised, as per Bruce Stenulson's discussion on EM sensitivities and what the symptoms of EM sensitivity is, basically it appears as traumatised fascia, binding down on the body organs and fluid pathways. I've made many casual observations over the years of being a therapist, and to my level of training, this is what I have witnessed occurring, when people claim miracle healings associated with Rife technology, at any level. It has often be said you don't need belief for Rife to work, true, but belief, hope, prayers, diet, any activity that leads to de-stressing will have effect on our fascia. I don't want to de-sensitise spiritual healings, or miracles from God, but when the body heals so fast and completely, then there has to be a physiological process taking place for this to occur. Medical Authorities have for years been coining these healings as placebo, the unknown mystical healing effect. Wrong. Fascia release has occurred, as an unknown effect of the drug or therapy provided. Entrainment, drugs, diet, Rife, exercise, meditation, prayer, they all effect how our fascia behaves, it is the body's memory of life experiences that have been delivered to it, manifest in a physical soft tissue that can dynamically change, almost instantly in its elastic and hydrated structure, either providing stress to body functions, or release and normalization of body functions. Regards, Ken Uzzell http://heal-me.com.au Frex - CHIamp Re: Re: RB tube losing power Hi , You are essentially right on target. Remember that you are periodically reversing polarity of the electrodes as the specific frequency is being transmitted through them. Yes, an analogue frequency generator supplying a clean sine wave through the contact pads or coils will, indeed do a pretty good job. Remember that this is most effective, as described, on localised injury or malady and is more marginal when treating " whole body " conditions. Again, the correct frequency is important, very important, as a more precise frequency requires significantly less power. Exact sinusoidal frequency is critical to success! Be a sharpshooter, not a shotgunner. As far as impedance matching between the contact pads and the body; a simple resistance match is achieved through a variable load matching network, similar to an audio speaker impedance matching circuit (only variable) after having taken a reading of the subject's body which is not difficult at all. Yes , it is really that simple. So many people have gone so far overboard in their attempts to complicate the simple that it is fast confusing the " little man " and causing many good and valuable people to abandon the pursuit of an end in this quest. The constant discussion of " scalar waves " , " harmonic distortion " , etc., etc., etc., clouds a relatively simple science. Search for the mysterious " Rife Effect " is the greatest myth of them all and has done more to hurt this science than the FDA. I personally want to thank you for this forum, your inputs, and your allowing all views, even those which are ridiculously off-track, because through all the din there are the occasional pearls of knowledge that are well worth the work of harvesting them. Yours Always, Dr. Ian MacLeod, Ph.D. Nielsen wrote: Correct me if I am wrong, but what you are describing below can be done with the unmodified output of a $200 function generator, and at far better than 10% distortion. Most will do 20Vpp without the kind of step-up transformer used in the Crane type devices. Even a free software generator and computer soundcard would give you a few volts. Aside from the exact sinewave frequencies, are there any criteria I am missing here. For example, how are you dealing with impedance matching between the pads and body? Do you really mean you have a positive and negative electrode, or do you have a positive and ground? Nielsen Dr. Ian MacLeod, Ph.D., New Lhasa Research Facility, In search of the truth through relentless research and infinite patience. Quote Link to comment Share on other sites More sharing options...
Guest guest Posted May 5, 2006 Report Share Posted May 5, 2006 Hi Ian I am requesting some expert advice on how to connect an 8 " Plasma Globe to my computer driven rife program, which is amplified by a 200watt stereo amp. I purchased my globe from Spencer's today and need help to hook it up so it will function properly. My knowledge of electronic's is limited. I will accept help from anyone in the group it they wish to. Thank You Emanuel On Mon, 1 May 2006 23:14:45 -0700 (PDT) Ian MacLeod writes: > Hi , > > Our IM007 produces about 1.20 - 24.5v. P.P. NLV (No Load Volts) > depending on the frequency generated. We are running it's signal > through an audio amplifier that is protected via Ground Fault > Interruption protection and also grounded to true ground. Inside > the amplifier are numerous redundant grounds and the amplifier > itself has been tweeked for accurate reproduction of sinusoidal > waveform and frequency. It is an analogue, Valve (Vacuum Tube) > audio amplifier and is extremely accurate through the range of 10hz > - 12.5Khz which is more than sufficient for our work. > > You may use a commercially available audio amplifier but I must > add this caviat: > PROTECT YOURSELF BY INSTALLING GFI AND TRUE GROUND PROTECTION TO > THE AMPLIFIER AND ANY AND ALL EQUIPMENT THAT IS POWERED FROM MAINS > ELECTRICITY! > > The ability to drive your lamp will depend on the output voltage > and, to a lesser extent, available current from your amplifier. If > you are using a transformer be aware that it will not reproduce a > clean sine wave except in an extremely narrow range of frequencies > (probably 40-70hz) unless it is specifically wound and loaded to the > frequency you are using. A deformed sine wave begins to produce > unwanted and unpredictable harmonics, not to mention that the coil > itself is a transmitter of these harmonics, and you have no idea > where you are " aiming " your frequencies (as there is no longer any > specifific frequency but a smattering of harmonics) even if your > coil is inside a Faraday Cage. > > We have modified a high voltage automobile " E-Core to Americans " > flyback-style ignition coil (inside a grounded Faraday Cage) with a > variable balancing coil so as to keep a clean sine wave at any > frequency. At present it requires rebalancing each time we change > frequencies significantly, but an automatic balancing system is not > far off according to my guru, . > > Best of luck to you. Remember that the applied voltage to your > tube will want to be at least 1500V so be careful! You can pull > quite a nasty little jolt from these toys! > > Warmest Regards, > > Dr. Ian MacLeod, Ph.D. > > martin7730 wrote: > Hi Ian, > > What voltage level is your IM007 driving your globe. > Today at Wallmart I just purchased an 8 " Electrostorm Globe and want > > to drive it with my stereo amp and step up transformer. > > As always I appreciate your time and dedication. > > > > Dr. Ian MacLeod, Ph.D., New Lhasa Research Facility, In search of > the truth through relentless research and infinite patience. > > --------------------------------- > Get amazing travel prices for air and hotel in one click on Yahoo! > FareChase > > Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You are posting as a guest. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.