Jump to content
RemedySpot.com

Re: Now: RFID and insomnia, Was: cell phone towers/ Marjij and

Rate this topic


Recommended Posts

Posted

Hello ,

you should not jump to conclusions when you read something that is not there.

I did not write that I touched the circuitry, but close to the glass of the

display.

All displays emit *dirty air*, only you cannot measure that.

The Spectran NF has a special prog. for RFID 13,56 MHz.

But also 125 kHz is used, as well as 860-950 MHz and 2.450 MHz.

RFID chips do not emit anything.

They are only sending when triggered.

Only then they are responding.

I have tried measuring those RFID chips in goods at the gates of supermarkets.

But you only get a signal when a RFID chip passes a detection gate without being

destroyed at the cash counter.

Of course when you are in places where a number of RFID readers are, your card

may respond.

And of course in industry complexes, where they want to know where the persons

are, and in which allowed rooms, the name tags will respond in every room.

But I can hardly imagine, that bank cards are emitting when not scanned.

Greetings,

Claessens

member Verband Baubiologie

www.milieuziektes.nl

www.milieuziektes.be

www.hetbitje.nl

checked by Norton

Now: RFID and insomnia, Was: cell phone towers/ Marjij and

charles wrote:

> btw, ALL digital displays show *dirty air*.

> ALL.

>

I don't doubt that, but the Cornet does not bother me, so that leads me

to believe some digital displays can be made acceptable quiet.

> They can be measured with special Detectors and spectrumanalysers with

special antennas.

>

> Curiously, when measuring, the probe or antenna must be held against the

elektrosmog source.

>

If the probe or antenna touch the circuitry, then it is no longer

measuring dirty air, but the circuit itself.

> At a distance of 1 " there is trouble in measuring, but an electrosensitive

person may be harassed by this source at a distance of 3 meters away!!

>

I see what you are saying. Just like RFID chips have an effect at

distance, but can't be measured without special detectors.

This seems a good time to tell this:

On Tuesday, Sep.21, I told my parents at the breakfast table about the

replacement bank card I got Saturday. The new card had an RFID chip in

it, also called Blink or PayPass. When I hold these wireless chips, I

get a headache, etc. So I tried to shield it over the weekend and put it

in the bathroom (away from bedroom). On Monday I called Chase to request

a replacement card without Blink.

Mom's light bulb turned on, she asked about the new credit cards they

received in June.

Eeeek! They have them too! And in dad's wallet he has been in close

proximity for the same length of time that he had been getting worse.

I first tried smashing the chip with a ball-peen hammer. I sat with mom

in the garage/shop on the opposite side of the room, and waited 20

minutes for the pain and other sensations to subside. Went over to hold

the card again. This time only a lesser sensation. Still emitting... So

next I drilled out the chip. I can now see the wires to the antenna in

the rest of the plastic. Now the feeling is mostly gone. I did the same

to the other 2 cards. The magnetic stripe is untouched and still works

at the gas station.

That night, we all slept better.

In fact mom said later the next week she has Really been sleeping better

all week since the RFID chips were destroyed. Very relaxed now. The

tinitus is still louder, but the insomnia is gone.

It seems important to tell that mom's card was in dad's den drawer until

one month prior, when dad insisted mom put it in her purse. That is when

mom really started having trouble sleeping. Didn't realize it until I

brought it up. Couldn't figure out what changed, that we couldn't sleep.

Mom was really tossing and turning, very distressed.

Dad had been unable to sleep lately, short of breath, and falling

asleep, even while we were talking to him.

His heart rate has been 35-40, but the blood oxygen sensor says 98%.

By the time we were in Spokane that October morning, dad was laughing

and joking in the hospital.

They scheduled tests later in the next week, and I took him home.

Those chips are nasty!

So check your cards for Blink))), and if you are not sleeping well,

definitely get them out of your pocket and away from your bed!

I asked Chase to replace that card... but they sent exactly the same

thing! I called them again and found the right wording to get the right

card. Tell them you want to OPT out of the Blink program (and get a new

card issued.)

Posted

> But I can hardly imagine, that bank cards are emitting when not scanned.

I have a work ID badge that bothers me when it is:

1) on my person, and

2) I am around strong EMF sources (computers, florescent lights)

I don't think the badge is emitting anything, but it could be

the antenna that's built into the badge to pick up a 100-150khz

signal combined with ambient EMF that's bothering me. I have tried

shielding it, and even once put it in a special badge holder

that " mis-tunes " the antenna so it doesn't respond to the

proximity transmitters (confirmed by my own testing), but

nothing eliminates my reaction to the badge other than getting

it away from me.

So yes, it's not emitting anything, but it still bothers me...

Marc

Posted

> I first tried smashing the chip with a ball-peen hammer. I sat with mom

> in the garage/shop on the opposite side of the room, and waited 20

> minutes for the pain and other sensations to subside. Went over to hold

> the card again. This time only a lesser sensation. Still emitting... So

> next I drilled out the chip. I can now see the wires to the antenna in

> the rest of the plastic. Now the feeling is mostly gone. I did the same

> to the other 2 cards. The magnetic stripe is untouched and still works

> at the gas station.

Perhaps your experiments answer my question as to what portion of my work

ID badge causes me the most trouble? I had thought that it might be the

antenna wire embedded in the badge, just because it is metal. However

from your experiments it sounds like it might be the chip that the

antenna connects to.

And I'll note that not all of these chips are bad. The previous generation

work ID badge that I used to have also had an antenna and a chip, but it

caused me no symptoms.

But the problems caused by these chips are easy to detect, as the

symptoms are strong & immediate. Unfortunately, I can't drill out

the chip on my work ID badge, because I need that functionality to

get into the building!

Marc

Join the conversation

You are posting as a guest. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...