Guest guest Posted December 24, 2010 Report Posted December 24, 2010 My last reply was pre-maturely sent, sorry about that. Okay, Marjij and . I am located in Central NJ. There are both plenty of people and plenty of wireless. I found that small you wrote very interesting, . I have yet to purchase any meters. Lessemf.com suggested that I need a meter for everyting in order to properly assess what is causing my symptoms. $850, yeah okay- while I'm hard pressed to find a place to live that I can afford which gets more challenging daily. What do you suggest for the novice , ?  For Marjij, where are you located--in WA, as well or are you seeking to relocate there? Have a great holiday season all.  So  were you the one who was attacked by the cell phones being turned off at a conference or was that Evie? >>> Are you in the US? >>> >> Yes, NE WA state. >> >> >> > Excuse me, but I can't tell from this exchange if it was Pamela or who said they lived in NE WA state. Sorry if it was not clear, I wrote the email, so it was me. Oh that is clear as mud. I am typing... and I have lots of pictures of NE WA on my webpage, so... > I am thinking of moving to Chewelah, WA can either of you give me some information about that area? I've been in that area several times, and have studied the locations of the hazards. This summer I drove to Valley for hay, and only two months ago, I drove Hwy 395 south to Spokane, with the Acoustimeter on the dashboard, and the audio plugged into the truck radio/CD-in. Makes a nifty hands free setup. Starting in Colville, they just put up a new tower across from the Walmart, so downtown is now very very bad. There are 3 towers on the hill 1 mile north on Colville Mtn, and another tower 2 Mi SE on Huckleberry Range Paradis Peak. Also the local AM radio tower is 1 Mi. south in the valley floor. I wrote down 0.54 V/m for Colville on the Acoustimeter, and on the Cornet, 0.258 mW/m2 outside the Walmart, and 4.807 mW/m2 inside Walmart, nearest the check out computers using WiFi, and the shelfing workers with their WiFi scanners. Avoid them like a plague! That is very much in the red zone. (I have a conversion table on my webpage.) Heading south 6 miles is Arden, and from here south it is actually fairly quiet for the next 8 miles to Addy, <0.02 V/m. Then I started picking up a cel-tower again. I located it when passing Blue Creek intersection 3 Mi south of Addy, there is a new tower just west 3/4 mile on the hill just opposite of, (south of) Rieckers Mtn. It was not there last year. I didn't write down any numbers, as I was on the highway, and didn't aim the meter at the tower. Continuing southeast, 5 Mi to Chewelah, the tower west of Chewelah becomes visible, and audible as the whine grows steadily. It is on the first hill west of the valley, but I can't remember which hill that was. Maybe Pine Hill. It looks like I forgot to update my map after that last trip... I think it is less than 2 years old. Downtown Chewelah, I wrote down 0.34 V/m. Only in the yellow zone. Fairly small bubble in radius. Worry more about the above tower than downtown stuff. South 1 mile, I got a large spike near the casino on the east side of Hwy395. I looked around hard, but couldn't see any towers to explain it. I didn't write down any numbers, but it was memorable. The next several miles past Jumpoff Joe Mtn, it is fairly quiet again, <0.02 V/m, as the surrounding hills provide good shading. I also found it fairly quiet south of Valley to Springdale where I got hay this year. Approaching Loon Lake, there is a tower on top of Deer Lake Mtn, east one mile of Hwy. From here south, there is no " quiet " on the meter, it is always buzzing and whining, with the intensity going up and down between towers etc. Approaching Clayton, I started picking up the radar from Spokane Airport, I noted 0.69 V/m at Clayton, every 11 seconds. From there south, the number of towers increase as you (or I) approach Spokane. There are 2 towers very close to, and in Deer Park. Right next to the Hwy. 0.87 V/m getting deep into the red zone again at the peak nearest those towers. Driving through Spokane is one tower after another, 2 V/m. One other measurement to share for Spokane, passing the Sears building on Division St, opposite a tall banking building, it has many antennas on top, I measured 4.07 V/m. That is seriously bad, and it really hurt. Back north to Chewelah, back in summer, when dad drove west with me on the Cedona-Addy Rd, I found the radio tower, and other towers on top of Stensgar Mtn blanketed that valley just to the north, I remember it showing up on my Zap Checker, but less so on the others. Acted more like an analog wave than a digital noisemaker. Dad thought those valleys might provide good protection from Spokane, with a warmer growing climate than here, but it didn't pan out. Second place he thought might work is a bit north in Swiss Valley. I was not feeling well enough to get excited about more exploring. I was pleasantly surprised to find those 2 quieter areas. The thing that bothers me about moving to Arden-Addy or Valley-Springdale, is it is more populated than here. But with several neighbors here broadcasting WiFi, the numerical statistic of 2 people per sq. mile just isn't what it used to be. Looks like I wrote a short book. Hope you find it educational, and helpful. > Cell danger? Thanks, > > Marji > > > > ------------------------------------ > > Quote
Guest guest Posted December 25, 2010 Report Posted December 25, 2010 http://www.tomsgadgets.com/products/details.aspx?pc=ED85EX Best Giles ES-uk.info >>> Are you in the US? >>> >> Yes, NE WA state. >> >> >> > Excuse me, but I can't tell from this exchange if it was Pamela or who said they lived in NE WA state. Sorry if it was not clear, I wrote the email, so it was me. Oh that is clear as mud. I am typing... and I have lots of pictures of NE WA on my webpage, so... > I am thinking of moving to Chewelah, WA can either of you give me some information about that area? I've been in that area several times, and have studied the locations of the hazards. This summer I drove to Valley for hay, and only two months ago, I drove Hwy 395 south to Spokane, with the Acoustimeter on the dashboard, and the audio plugged into the truck radio/CD-in. Makes a nifty hands free setup. Starting in Colville, they just put up a new tower across from the Walmart, so downtown is now very very bad. There are 3 towers on the hill 1 mile north on Colville Mtn, and another tower 2 Mi SE on Huckleberry Range Paradis Peak. Also the local AM radio tower is 1 Mi. south in the valley floor. I wrote down 0.54 V/m for Colville on the Acoustimeter, and on the Cornet, 0.258 mW/m2 outside the Walmart, and 4.807 mW/m2 inside Walmart, nearest the check out computers using WiFi, and the shelfing workers with their WiFi scanners. Avoid them like a plague! That is very much in the red zone. (I have a conversion table on my webpage.) Heading south 6 miles is Arden, and from here south it is actually fairly quiet for the next 8 miles to Addy, <0.02 V/m. Then I started picking up a cel-tower again. I located it when passing Blue Creek intersection 3 Mi south of Addy, there is a new tower just west 3/4 mile on the hill just opposite of, (south of) Rieckers Mtn. It was not there last year. I didn't write down any numbers, as I was on the highway, and didn't aim the meter at the tower. Continuing southeast, 5 Mi to Chewelah, the tower west of Chewelah becomes visible, and audible as the whine grows steadily. It is on the first hill west of the valley, but I can't remember which hill that was. Maybe Pine Hill. It looks like I forgot to update my map after that last trip... I think it is less than 2 years old. Downtown Chewelah, I wrote down 0.34 V/m. Only in the yellow zone. Fairly small bubble in radius. Worry more about the above tower than downtown stuff. South 1 mile, I got a large spike near the casino on the east side of Hwy395. I looked around hard, but couldn't see any towers to explain it. I didn't write down any numbers, but it was memorable. The next several miles past Jumpoff Joe Mtn, it is fairly quiet again, <0.02 V/m, as the surrounding hills provide good shading. I also found it fairly quiet south of Valley to Springdale where I got hay this year. Approaching Loon Lake, there is a tower on top of Deer Lake Mtn, east one mile of Hwy. From here south, there is no " quiet " on the meter, it is always buzzing and whining, with the intensity going up and down between towers etc. Approaching Clayton, I started picking up the radar from Spokane Airport, I noted 0.69 V/m at Clayton, every 11 seconds. From there south, the number of towers increase as you (or I) approach Spokane. There are 2 towers very close to, and in Deer Park. Right next to the Hwy. 0.87 V/m getting deep into the red zone again at the peak nearest those towers. Driving through Spokane is one tower after another, 2 V/m. One other measurement to share for Spokane, passing the Sears building on Division St, opposite a tall banking building, it has many antennas on top, I measured 4.07 V/m. That is seriously bad, and it really hurt. Back north to Chewelah, back in summer, when dad drove west with me on the Cedona-Addy Rd, I found the radio tower, and other towers on top of Stensgar Mtn blanketed that valley just to the north, I remember it showing up on my Zap Checker, but less so on the others. Acted more like an analog wave than a digital noisemaker. Dad thought those valleys might provide good protection from Spokane, with a warmer growing climate than here, but it didn't pan out. Second place he thought might work is a bit north in Swiss Valley. I was not feeling well enough to get excited about more exploring. I was pleasantly surprised to find those 2 quieter areas. The thing that bothers me about moving to Arden-Addy or Valley-Springdale, is it is more populated than here. But with several neighbors here broadcasting WiFi, the numerical statistic of 2 people per sq. mile just isn't what it used to be. Looks like I wrote a short book. Hope you find it educational, and helpful. > Cell danger? Thanks, > > Marji > > > > ------------------------------------ > > Quote
Guest guest Posted December 25, 2010 Report Posted December 25, 2010 Hi, pamela clemonts wrote: > I need a meter for everyting in order to properly assess what is causing my symptoms. $850, yeah okay- while I'm hard pressed to find a place to live that I can afford which gets more challenging daily. What do you suggest for the novice , ? > Not an easy question. That probably explains the length of my ehs page, attempting to point out each meter's strengths and weaknesses. Right now, Cornet has the lowest price, and best visual display, but is not sensitive enough outside of the urban environment. The audio analysis of the Acoustimeter is the most useful way to sweep an area or evaluate computers, tv, phones, wifi, etc. Determine where and what you want to measure, then choose or wait for newer models. > So were you the one who was attacked by the cell phones being turned off at a conference or was that Evie? > For me, it was not at a conference. I stay around home 99% of the time. http://seahorseCorral.org/ehs1.html Quote
Guest guest Posted December 26, 2010 Report Posted December 26, 2010 Hello , as I wrote to you before, in your comparison on your website, you are *comparing apples with onions*. In other words, it is complete inapropriate. You may not connect an antenna (which should be hold vertical and not horizontal) with a 1 m cable to a meter, which cannot be adjusted for that. The small WiFi antenna is useless. RMS measurements cannot be compared to *Peak values* of broadbandmeters. Why don't you use the latest LCS software? Which is free. There you can choose the correct frequency bands. Also for uplink of your mobile phone. PS. A meter for everything does not exist yet. One needs at least two different ones. With a Spectran NF and some extra's, one can measure *dirty power* as well as *dirty air*. And it is my belief, that this *dirty power* as well as *dirty air* are more dangerous to our health than the mobile phone masts! (Mobile phone masts are also emitting *dirty air*, which when reaching the walls of your home are transfered into your mains, and become *dirty power* there.) Greetings, Claessens member Verband Baubiologie www.milieuziektes.nl www.milieuziektes.be www.hetbitje.nl checked by Norton Re: Re: cell phone towers/ Marjij and Hi, pamela clemonts wrote: > I need a meter for everyting in order to properly assess what is causing my symptoms. $850, yeah okay- while I'm hard pressed to find a place to live that I can afford which gets more challenging daily. What do you suggest for the novice , ? > Not an easy question. That probably explains the length of my ehs page, attempting to point out each meter's strengths and weaknesses. Right now, Cornet has the lowest price, and best visual display, but is not sensitive enough outside of the urban environment. The audio analysis of the Acoustimeter is the most useful way to sweep an area or evaluate computers, tv, phones, wifi, etc. Determine where and what you want to measure, then choose or wait for newer models. > So were you the one who was attacked by the cell phones being turned off at a conference or was that Evie? > For me, it was not at a conference. I stay around home 99% of the time. http://seahorseCorral.org/ehs1.html ------------------------------------ Quote
Guest guest Posted December 26, 2010 Report Posted December 26, 2010 Hello , btw, ALL digital displays show *dirty air*. ALL. They can be measured with special Detectors and spectrumanalysers with special antennas. Curiously, when measuring, the probe or antenna must be held against the elektrosmog source. At a distance of 1 " there is trouble in measuring, but an electrosensitive person may be harassed by this source at a distance of 3 meters away!! Greetings, Claessens member Verband Baubiologie www.milieuziektes.nl www.milieuziektes.be www.hetbitje.nl checked by Norton Re: Re: cell phone towers/ Marjij and Hi, pamela clemonts wrote: > I need a meter for everyting in order to properly assess what is causing my symptoms. $850, yeah okay- while I'm hard pressed to find a place to live that I can afford which gets more challenging daily. What do you suggest for the novice , ? > Not an easy question. That probably explains the length of my ehs page, attempting to point out each meter's strengths and weaknesses. Right now, Cornet has the lowest price, and best visual display, but is not sensitive enough outside of the urban environment. The audio analysis of the Acoustimeter is the most useful way to sweep an area or evaluate computers, tv, phones, wifi, etc. Determine where and what you want to measure, then choose or wait for newer models. > So were you the one who was attacked by the cell phones being turned off at a conference or was that Evie? > For me, it was not at a conference. I stay around home 99% of the time. http://seahorseCorral.org/ehs1.html ------------------------------------ Quote
Guest guest Posted December 26, 2010 Report Posted December 26, 2010 Greetings , > as I wrote to you before, in your comparison on your website, you are *comparing apples with onions*. > Comparing between different meters? or the way I am taking measurements? Please clarify. > In other words, it is complete inapropriate. > I am an apprentice with no master on hand to teach me. > You may not connect an antenna (which should be hold vertical and not horizontal) I agree the first 3 pictures of the hyperlog antenna are not held vertical. Does that make the higher reading from pointing at the rocks invalid? I would like to know why I get a higher reading pointing down. The next time I am up there I'll do the test again with vertical polarity. The picture from Jun12 I found the highest reading 30 degrees from vertical. Can anybody explain that? > with a 1 m cable to a meter, which cannot be adjusted for that. > It is true I don't have the calibration specs to make the numbers accurate for non-supported hardware. So I added a disclaimer that using that antenna does make the Cornet more like a detector, and not calibrated power readings. Is that not good enough? or should I erase the whole paragraph and 3 pictures? This was my experience in taking measurements. Sometimes I did it wrong. I hope I added enough explanation to my little book, to help others learn from it, and not repeat mistakes. > The small WiFi antenna is useless. > Which one, the one at the bottom? I agree. That was the point. Or the whip antenna that comes with the Cornet? I would say it is not very sensitive, thus the attempt to use the hyperlog antenna, or at least show using the better antenna makes better results. Maybe I should get the Cornet Log-Periodic antenna for the ED85EX (to compare the two special antennas.) > RMS measurements cannot be compared to *Peak values* of broadbandmeters. > Yes, measuring peak is not the same as average. The manual for sweeping an area says to only use peak values to determine exposure. I don't have the term RMS anywhere on my page. The word " average " only appears when describing the characteristics of a Wifi beacon, as it is not the same as a data transmission. Ah, I do have RMS graphs for the Spectran, but that is to be complete in comparing the various settings available. Confusing is what that becomes... which setting is right for each frequency band and type of transmission? > Why don't you use the latest LCS software? Yes, let's talk about the Spectran. I am using LCS 1.9.9.9 to get this years graphs from the Spectran. Version 2.0 requires a newer version of windows, which will not run on this IBM Thinkpad. I have purchased enough new hardware thank you. I don't need newer software to capture the output from the Spectran across the USB cable. > There you can choose the correct frequency bands. I don't have the newest _scanprofile_ file from LCS version 2, true. > Also for uplink of your mobile phone. > That is Funny, ia asked _ME_ for the frequency band for the USA G3 phones when I told them their profile list did not include it. The phone I measured, it is not My phone!, I tried the entire frequency range from 800 - 1000 MHz and 1800 - 2000 MHz to be sure I wasn't missing it, but in the picture you reference, it is scanning 824 - 849 MHz which is what is supposed to be used in rural USA, and where I got a blip in the video my camera recorded. I can't figure out how to prove to myself or ia the meter does or doesn't work right, and they can't tell me what test to perform that proves it is working correctly. So when I was last in Spokane, I saved the Spectran recordings from every profile in the list, running LCS, and sweeping in a circle, both horizontal and vertical polarity. Only the 1900Mhz GSM band produced results when I aimed vertically at nearby towers, which is correct for urban phones, but not the right frequency for dual-band rural phones. The signal over background was 25 dBm while sweeping toward and away from towers only 860m (1/2 mile) away. http://seahorseCorral.org/images/meter/20101118_Spectran4-HL7060-LCS_Spokane-194\ 0MHz-860m-sweep_4340-800.jpg Also down inside the parking garage, I recorded with LCS this one: http://seahorseCorral.org/images/meter/Sweep-1M-800.0M-950.0M-20101001.0914-100m\ sN-AmpOff_Spokane-602.png So it looks like it works, but comparing version 4 with version 2 recordings, makes it look like something is wrong. I certainly can't sweep an area anymore by driving through it, like I used to. But this doesn't address my unwillingness to use it due to it's strong emissions. I paid heavily healthwise getting those recordings, having put off that kind of test for 4 months, and am at a standstill or impass, regarding that meter. > PS. A meter for everything does not exist yet. > Very true. That is definitely why I hesitate to recommend any one meter as The solution. > One needs at least two different ones. > HF, and LF yes., Plus magnetic, plus electric fields, and there still exists nothing to measure the effects from RFID chips, Q-link etc pendants... There is definitely a gap in understanding how and what are affecting (us). > With a Spectran NF and some extra's, one can measure *dirty power* as well as *dirty air*. > I am not buying another Spectran. The only meter I have to measure dirty power, is the GS meter. I don't doubt there are other low frequencies to be seen. > And it is my belief, that this *dirty power* as well as *dirty air* are more dangerous to our health than the mobile phone masts! > Because they are closer to home, I agree. > (Mobile phone masts are also emitting *dirty air*, which when reaching the walls of your home are transfered into your mains, and become *dirty power* there.) > Yes, every ungrounded wire becomes an antenna. So what apples and onions are on my page that need to be erased, or clarified, or have the test repeated correctly? Quote
Recommended Posts
Join the conversation
You are posting as a guest. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.